STM32 Firmware for CAN Communication (Brazil Project)

$250-750 USD

Suljettu

Julkaistu

lähes 3 vuotta sitten

$250-750 USD

Maksettu toimituksen yhteydessä

We are looking for a company/freelancer with experience developing firmware, CAN protocol, node-red, STM32F103RG, C/C++ The physical project consists of two modules: a CPU module and a remote IO module(slave), each with its own power supply. They need to communicate via CAN protocol. The CPU consists of a BeagleBone Black board and an expansion slot with: 2 CAN, RS485, RS232, Profitbus, and a power supply. The remote module is based on the STM32F103RG chip, with an USB slot, and a CAN slot, and a temperature sensor. The challenge is to develop the firmware and driver to allow these two modules to communicate (node-red). If the above description is down your alley, please contact us so we can send more info. Recently completed a CAN firmware for STM32F103C8T6 to communicate with a Solar System and display the parameters (Temperature, Voltage, battery level, etc) on an OLED in real-time. Please contact now

Electrical Engineering

Projektin tunnus (ID): 30238500

Tietoa projektista

4 ehdotukset

Etäprojekti

Aktiivinen 3 vuotta sitten

Haluatko ansaita rahaa?

Sähköpostiosoite

Freelancerin tarjouskilpailun edut

Aseta budjettisi ja aikataulu

Saa maksu työstäsi

Kuvaile ehdotustasi

Rekisteröinti ja töihin tarjoaminen on ilmaista

4 freelancerit tarjoavat keskimäärin $632 USD tätä projektia

@Alif2710

Hi. Nice to meet you, Elektronic Expert here, you can Look at my Profile for my past project I have read your description, I already and finish do the same project about CAN BUS on Car Using STM32F4, So, for this project i can do all the firmware on STM32 but not for Beaglebone firmware for the STM32 Software please use STM32CubeIDE You can sent me a message to talk for detail, Tell Me What your Problem, and let me help you to solve it Best regards, Alif

$650 USD 7 päivässä

5,0

(1 arvostelu)

2,0

@muraliprogi

Dear Client, I have 10 plus years of experience in embedded systems and Automotive product development good knowledge in Product development life cycle. Expertise in 8,16,32 bit microcontrollers and Analog circuit design and power drivers. Good knowledge to handles wireless modules, Bluetooth,GSM,IOT and UART I2C, SPI, CAN Protocols. We need a short discussion with you for our better understanding.

$611 USD 15 päivässä

0,0

(0 arvostelua)

0,0

@surajsoni401

Hello There, Hope you're doing well. IoT Technologies :  IoT Protocols : MQTT, CoAP, HTTP, TCP/UDP, IPv4, IPv6, 6LoWPAN and REST  IoT Platforms : AWS IoT, thingspeak, Freeboard, IFTTT, Blynk  IoT/M2M Client/Broker:Mosquitto and HiveMQ MQTT broker, cloud mqtt, adafruit.io.  Full Stack Programming Languages : C, C++, C#, C# UWP, C# MVC, Java, spring boot, hibernate, mysql, Python, Java, Node, Node Red, AWS IoT, GCP, And various IoT Protocols.  Wireless Device Protocols : 1. Wi-Fi: NodeMCU, Raspberry Pi 3 2. BLE: TI CC2541, CC1350, HM-10, HC-05 3. Sub-1 GHz: CC1310, CC1350 4. Cellular: SIM800/900 GSM Module 5. GPS: Neo 6M V3 Warm Regards, Suraj Soni

$600 USD 7 päivässä

0,0

(0 arvostelua)

0,0

@eehzux

During my master's degree, I have developed can communication driver for vehicle mounted millimeter wave radar, so I have experience in this field. We can further communicate how to cooperate and help you complete the project as soon as possible. thank you!

$666 USD 15 päivässä