Sulautetut järjestelmät Jobs

Hi I will share the details with the shortlisted candidates. Thanks

We are developing a luxury smart ring wearable and are looking for an experienced hardware engineer to design a compact PCB/FPC for this device. This is a very small wearable device, so experience with ultra-compact electronics is essential. Device concept: Smart ring with biometric sensors and Bluetooth Low Energy connectivity. Main components planned: • Nordic nRF5340 BLE SoC • MAX86174 optical biometric sensor (PPG) • ICM-42670 motion sensor (IMU) • TMP119 temperature sensor • nPM1304 power management IC • External SPI Flash memory • Li-Po micro battery Design constraints: • Ring thickness target: 3–3.5 mm • PCB width: approx 5.5 mm • PCB length: approx 26–30 mm semicircle layout • Extremely low power consumption ...

1: Simple Arduino device detecting a switch from a device 2: 2 RBG light strips with 16 LEDS 3: 4 input outputs for on and off

I look for hardware developer. Electronics schema and pcb designer.

Quiero que revises y mejores mi circuito basado en un Xiao ESP32-C3 que controla una tira EL de 1,65 m mediante un inversor 3,7 V DC → 100 V AC, un sensor táctil TTP223 y un MOSFET lógico (AO3400, IRLZ44N o SI2303). Lo que más necesito es la mejora del circuito existente, poniendo el foco en la optimización de la eficiencia energética. Aunque sé que el mayor consumo proviene de la propia tira EL, quiero exprimir al máximo la batería Li-ion de 1 600 mAh para alargar la autonomía más allá de las 4 h actuales sin sacrificar brillo. Tareas concretas • Proponer el esquema más compacto posible, manteniendo componentes SMD de fácil adquisición. • Seleccionar el MOSFET l&oacut...

I am looking for an engineer or a small engineering team to help build a working prototype of a wearable smart ring that communicates with a thin wallet card device placed in a wallet. The purpose of the device is to prevent wallet loss by alerting the user when the wallet moves more than a short distance away from the ring. The system should provide two types of alerts: a vibration alert in the ring and an optional audio alert. The project goal is to create a fully working prototype that demonstrates the concept in real life. Experience with miniature electronics, wearable devices, Bluetooth communication, and prototype development is preferred.

I’m building a small arcade-style attraction made up of six identical stations. Each station will recognise when its hand-held controller is lifted by means of a magnetic sensor—or any other proper kind of sensor —then launch a three-minute countdown. Here is the user flow I need you to realise: 1. Controller is lifted → internal timer starts. 2. An OLED screen at that station immediately shows the remaining time, counting down in real time. 3. When the three minutes expire the screen simply replaces the countdown with a clear “Game Over, move to next zone ” message + a buzzer or light; 4. Once the controller is set back the system must reset itself, ready for the next player. Hardware thoughts so far: magnetic (reed or Hall) sensor to detect li...

I have a commercial IR-band Laser device with essentially two "Modes" - NORMAL and TRAINING, or restricted. Switching between the two can only be accomplished by accessing the Firmware via a proprietary 8-pin connection, for which I do not have a cable or interface. The candidate must either A) build a custom breakout to connect to the proprietary connector, or B) modify the OEM CONTROLLER pad and cable. Once the system is accessed, no custom coding, overwriting, or modification of the firmware will be required; the Candidiate need only identify the language, access the settings, and "flip the switch" between the two settings profiles. The hard part will be creating the connection. Something as simple as a POGO pin may be sufficient, but I am not qualified to say. T...

Title: Industrial PCB Design for Arduino-based 4-Pump Chemical Dosing System ​Description: I am looking for a professional PCB designer to create a robust, industrial-grade PCB for a chemical dosing system. The project is based on an Arduino Uno and must be designed to eliminate EMI noise from inductive loads. ​Key Technical Requirements: ​Microcontroller: Arduino Uno (Socketed on the PCB). ​Outputs: Control for 4x DC Pumps (24V) and 1x Solenoid Valve via Opto-isolated Relays. ​Power System: 24V DC Main Input with a Resettable Fuse (PPTC) for protection. ​Noise Immunity: Must include Flyback Diodes (1N4007) for each output and proper decoupling capacitors for logic stability. ​Isolation: Separate ground planes for Logic (5V) and Power (24V) to prevent interference. ​External Interface: Hea...

I am looking for an experienced mobile app designer/developer to help create the first prototype (MVP) of a mobile app Please let me know if you have experience designing sports performance or wearable technology apps, and if you can share examples of your previous work. Thanks

Hi everyone, I’m currently looking for a talented freelancer who has strong experience with Flowcode 10 and can create an amazing and efficient program for a project I’m working on. -Must be comfortable building programs in Flowcode 10 -Able to design clean, well-structured logic and functionality -Experience with microcontroller projects is a plus If you’re skilled with Flowcode and interested in collaborating, please comment below or send me a direct message with: • A short introduction • Your experience with Flowcode • Examples of previous work (if available) Looking forward to working with someone passionate about building great programs!

We need a board that "translate" signal from DMX to led strip pixel adressable. Need to integrate RGB and RGBW pixel in various protocol, with clock or only data. Only one data signal needed (170 rgb pixel or 128 rgbw pixel to complete universe) -Possibilities to set start adress -Possibilities to control multiple pixel as one pixel (grouping for have total of 2x or 3x o 4x pixel controlled) -Setting IC ,Address and Grouping by dipswitch or other way accepted (also usb serial with proprietary software) -ALL SETTINGS NEED ALSO TO BE SETTED BY RDM -Usb or serial connector for upload firmware We are open to every system from arduino to anything. Need to be thinked in hardware and software side. Other this one we need a variant with pwm rgbw output with same feature like RDM, ...

I need the internal circuitry of the KK-82MS scientific calculator documented so I can design a drop-in replacement PCB. Your job is to open the unit, trace every relevant signal, and give me a clear map of what connects where. The focus is on both LCD behaviour and the button-scanning scheme, so I expect you to show how each LCD segment is driven, which pins act as commons, how the microcontroller multiplexes them, and the exact keyboard matrix rows and columns the processor polls. Feel free to combine a logic analyser, multimeter, oscilloscope, or any other bench tool you trust; choice of instrumentation is up to you as long as the final data are unambiguous. Deliverables • High-resolution photos of the calculator fully disassembled, including close-ups of the flex cables and IC m...

I have a stable FreeRTOS-based firmware that currently compiles only under my portable Arduino IDE 1.8.13 setup for the SAMD51 MCU. I now want the project to build and run cleanly in the latest Arduino IDE without carrying along any of those version-specific hacks, board package pin-tweaks, or legacy library work-arounds. Once the codebase is modernised, the next step is to extend it with new sensors. You will receive the present firmware, board-support files, and the partial sensor drivers at project start.

Hi, I'm looking for an experienced PCB designer to create a custom carrier/breakout PCB for a compact handheld device. No firmware or software needed — design only. Core Module: LILYGO TTGO T-Call V1.3 (ESP32 + SIM800L GSM) — mounted on the PCB via pin headers Components to integrate on PCB: OLED Display (SSD1306 128x64, I2C, 4-pin): Mounted above the PCB using standoff spacers — 4 mounting holes required Height will be adjusted with standoffs 4-wire cable from display soldered directly to PCB pads Buttons: 1x membrane switch connector (2-pin) for main button 2x additional button footprints connected to spare GPIO pins (for future use) Buzzer: Passive buzzer mounted directly on PCB Connected to designated GPIO via NPN transistor + flyback diode driver circuit ...

I need an engineer or team to create a working design for a parcel dimensioner that rivals the accuracy and reliability of a Cubiscan 325. The unit will live in a busy warehouse environment, so durability and quick “drop-and-scan” operation matter as much as precision. It doesn't have to be a similar design, but a similar function and success rate at measuring small irregular objects to the same size capability. Scope of measurement • Mixed-material parcels (paper, cardboard, plastic—anything that routinely moves through a fulfillment line) • Dimensions captured: length, width, height only—weight integration is not required at this stage Core expectations I’m looking for a complete, production-ready package: mechanical layout, electronic...

I need a complete hardware-and-firmware solution that blends a PIC microcontroller with Arduino-compatible modules on a custom-made PCB. The end goal is to streamline several industrial processes, and I also want the design flexible enough to drive lighting, heating & cooling, and security subsystems that resemble home-appliance automation. Here is what I envisage: • Schematic and PCB layout ready for fabrication, including a clean separation between the PIC control core and any auxiliary Arduino shields or sensor breakouts. • Embedded C / Arduino-style firmware that handles real-time control loops, sensor inputs, and actuator outputs for an industrial environment. • A concise BOM with component part numbers that are actually in stock. • Production-ready Ger...

I’m building a microcontroller-based system around an stm32 and need compact, reliable embedded-C firmware that lets me read multiple sensors and move their data cleanly through standard communication channels. The core of the job is classic microcontroller programming: bring up the chip, initialise the peripherals that the sensors require (typical I²C, SPI or simple GPIO timing), perform periodic reads, apply any basic filtering the devices recommend, then expose the results over the communication protocols we agree on—UART is mandatory; CAN or USB-CDC would be a welcome extra if time allows. You will be working with the latest STM32CubeIDE tool-chain, so please be comfortable with HAL and, where efficiency demands, direct-register work. I’ll supply full pin-outs, ...

I'm seeking an expert to prototype the electric chassis wiring for an electric trolley designed to transport tools. Key requirements include: - Design and implement wiring for electric chassis - Ensure safety and reliability Ideal skills and experience: - Electrical engineering background - Experience with electric vehicle wiring - Strong problem-solving skills Please provide relevant experience in your bids.

Note - I want someone to make & get one machine ready for me so please bid if you can handle everything from design to manufacturing. I am developing a compact, battery-powered device that continuously feeds a roll of sticky mat across a doorway so the exposed surface always stays clean. The concept is simple: a fresh section of mat is pulled from one spindle, laid flat, and the used layer is wound onto a take-up reel. Here’s what I already know I want: • Time-based automatic control that advances the mat precisely every hour. • A low-profile, walk-safe deck suitable for hospital corridors and dusty construction entries alike. • A rigid steel frame for durability, yet light enough to remain truly portable. • Quiet, sealed gear-motor driven by a rechargeable ...

I’m looking for an experienced developer who can build fully emulated firmware for a DMA card. The firmware should be compatible with Windows and capable of emulating several key functionalities, including: 100% CFG The configuration space of the firmware should perfectly replicate that of a legitimate device, allowing it to be detected and recognized by the system as authentic hardware. BAR Support BAR (Base Address Register) represents the memory region inside a PCIe device. The BIOS reads this information in order to properly communicate and interact with the device. Emulation Correct BAR handling ensures that when a driver sends a request to the PCIe device’s BAR, the firmware responds with the appropriate data, effectively imitating the behavior of a real device. Full ...

The original schematics and firmware sources for my existing motherboard are no longer available, yet I still need to keep the product alive and solve a series of recurring hardware failures. The immediate objective is to reverse-engineer the board in detail so I have a complete, accurate picture of how every power rail, I/O interface, and embedded controller is wired and programmed. Once that knowledge is captured, I want a refreshed design that removes today’s failure points and is ready for a short production run. Work starts with non-destructive teardown, high-resolution imaging, net tracing, and firmware dumping via JTAG/SWD or any other proven technique. From there the task moves into schematic recreation (Altium Designer or KiCad preferred), BOM generation with current compon...

Project Overview This project aims to develop a small WiFi gateway that connects to a Danfoss EKC 202C refrigeration controller via Modbus RTU (RS-485) and provides a local web interface. The system should allow monitoring of key controller values and limited control via a browser. The first version is a local-only solution without cloud connectivity, but the architecture must allow future expansion to cloud services. Hardware Assumptions • ESP32 or similar WiFi-enabled microcontroller • RS485 interface module for Modbus RTU communication • Connection to Danfoss EKC 202C controller (via Modbus adapter) Setup Flow • On first boot the device starts its own WiFi Access Point • User connects via smartphone or laptop • User opens configuration page at • Use...

I’m putting together an all-terrain rover that pairs a Raspberry Pi 5 with an Arduino. The Arduino will sit close to the hardware, polling and driving everything from temperature-humidity probes and distance sensors to an IMU (pitch/yaw/roll, altitude, compass), ESC-PWM motor controllers, speed-over-ground tracking and battery-management read-outs. All of that raw data needs to flow up to the Pi, where it is bundled, logged and pushed over a 4 G link. The Pi also runs the user interface on an onboard touchscreen. I want that interface to launch straight into a clean dashboard with drag-and-drop style widgets so I can rearrange or resize gauges, graphs and buttons while in the field. On the software side I need: • Firmware for the Arduino that publishes every sensor value pl...

I’m building an automated live-play poker table and need the complete RFID hardware blueprint that will let software read every chip on the felt in real time. The table will hold well over 100 tagged chips at once, and I want reliable High-Frequency (13.56 MHz) reads at a maximum distance of about 10 cm from the antennas under the layout. Your task is purely on the hardware side: define an architecture that can see each chip as stacks move, bets slide, and pots grow, then pass clean data to the software team through a simple API or wired interface of your choice. Key expectations • Robust HF antenna array layout sized for a poker table, including multiplexing strategy to handle >100 simultaneous tags without collisions or dead zones. • Reader, controller, and MCU/FPG...

I need a compact 2-4 channel analog MEMS microphone array built around an XMOS processor. The board must perform real-time beamforming, echo-cancellation and noise-suppression, then expose a clean audio output through straightforward header pins so it can be patched into downstream hardware without fuss. Size matters here: the smaller the PCB, the better. I’m expecting you to handle the full hardware cycle—schematic capture, PCB layout, component selection and a ready-to-order BOM—plus the XMOS firmware that brings the DSP features to life. Your code should compile and run on the free tools from XMOS; please include any scripts or tuning utilities you rely on. Deliverables • Production-ready Gerbers, pick-and-place file, annotated schematic • BOM with supp...

I’m building a small-footprint PCB around the ESP32 that will serve as the core of several IoT devices. The board must expose reliable Wi-Fi, Bluetooth, and flexible sensor headers so it can drop straight into prototypes and low-volume production runs. Here is the scope I have in mind: • Schematic capture for the ESP32 module with stable power-management, antenna clearance, and USB-to-UART programming interface. • PCB layout (2-layer is fine if performance allows) that remains within 50 × 50 mm, ready for standard SMT assembly. • Breakouts or onboard footprints for common environmental sensors; I haven’t finalised the exact parts, so leave room on I²C and a couple of ADC/GPIO lines for temperature, humidity or motion modules. • Production...

Wir entwickeln ein Music Tech Produkt, das die komplette Signalkette von E Gitarre und Bass bis zum Lautsprecher in einem System abbilden soll. Das System vereint kabellose Übertragung, Echtzeit Audio Processing, ein App Interface für Presets und Steuerung sowie eine Plattform Perspektive, sodass Sounds und Setups reproduzierbar werden und später erweitert werden können. Unser Fokus liegt auf einem bühnen und tourtauglichen Workflow, der auch in realen und stark gestörten 2,4 GHz Umgebungen stabil funktioniert. Es existieren bereits Hardware Prototypen und mehrere Iterationen von Sender und Receiver, unter anderem auf Basis von STM32 und ESP32. Die Zusammenarbeit ist auf mindestens zwölf Monate ausgelegt. Für die Rolle gibt es die Möglichkeit, ...

Client needs a VoIP Intercom Station operating in Standards Based SIP. Developer must have experience working with SOC like NanoPI and OrangePI. Developer must meet the following list of requirements so as not to waste our time. Embedded Linux Development Strong experience developing software for embedded Linux systems Experience with custom Linux distributions (Debian/Ubuntu) Kernel configuration, device drivers, and hardware interface support Bootloader and system startup (U-Boot or similar) Experience working with flash-based storage systems Linux system optimization for embedded hardware VoIP / SIP / Networking Experience implementing or maintaining SIP-based communications systems Knowledge of RTP / RTCP media streaming Familiarity with VoIP codecs such as G.711, G.729, Speex Un...

I need a custom power supply designed specifically for consumer electronics, with a focus on automation systems. The power supply must output 12V. Key requirements: - Suitable for consumer electronics and automation systems. - 12V output voltage. Ideal skills and experience: - Expertise in power supply design. - Experience with consumer electronics and automation systems. - Knowledge of safety standards and regulations. Please provide your portfolio and relevant experience.

My drone refuses to finish its latest firmware update and is now stuck in an endless restart loop. I need an experienced developer who has already dealt with drone firmware quirks to track down the root cause, flash the correct binaries if necessary, and get the aircraft flying again. The work is strictly troubleshooting: no new features or redesigns—just a clean, stable fix. While the main symptom is a failed firmware load, I’m open to your testing any related areas such as connection hand-shake or crash logs if you suspect they’re part of the problem. Deliverables • Diagnose the exact point where the firmware update fails • Apply or guide me through the corrective procedure (new build, bootloader tweak, or safe-mode flash) • Verify that the dr...

Looking for a wiring harness designer / electrical consultant to guide us on oven wiring, especially for LCD display integration, controller connections, wire routing, connector selection, and heat-safe harness design. Need practical consultation on: display wiring power vs signal wire separation routing through door hinges / moving sections connector and cable selection high-temperature protection manufacturable harness design Experience in appliances, industrial equipment, ovens, incubators, or similar systems is preferred. Please share: relevant experience similar projects display/HMI wiring experience high-temperature wiring experience Add these screening questions to filter better candidates: Have you designed wiring harnesses for ovens, appliances, or heated equipment?...

Looking for an electronic hardware designer / embedded consultant to help select the right low-cost, reliable, and easily sourceable microcontroller in India for products like ovens, incubators, and similar equipment typically employing a PID controller, a LCD/SPI/UART based display with read/write USB option and few IOs. Need someone who can handle both: technical recommendation of the microcontroller commercial sourcing guidance in Hyderabad / India The person should be able to suggest the best MCU based on cost, availability, reliability, peripherals, and production scalability, and also guide on vendors/distributors, pricing, MOQ, and backup sourcing options. Experience in embedded systems, industrial electronics, BOM optimization, and Indian electronics sourcing is strongly prefe...

I’m integrating a NEMA-17 stepper into a small robotics prototype and need reliable position feedback. My current hardware stack is an Arduino Uno, a standard A4988 driver, and an incremental rotary encoder mounted on the motor shaft. What I need from you is a clean, well-commented sketch that: • Drives the stepper using the A4988, • Reads the encoder in real time, • Reports absolute position (in steps or degrees) over Serial, and • Lets me set a target position via Serial and have the motor move there, stopping within one encoder count. Please include a brief wiring diagram (hand-drawn or Fritzing is fine) so I can replicate your setup, and note any libraries you rely on beyond the Arduino core. I’ll consider the job complete once the code compi...

I have a multi-rotor nanodrone running ArduPilot that must fly semi-autonomously via GPS waypoints. The core of the job is to configure the ArduPilot stack so the craft can: • Accept a pre-loaded waypoint flight plan • Accept inject, delete, or reorder waypoints in real time through a long-range data link • Provide the FC ready to integrate: on-board camera, LiDAR, other UARTS devices • Execute a dependable Return-to-Home routine triggered by failsafe, low battery, or a command from the ground station I already have the flight controller, ESC, batteries, motors, associated wiring, and drone frame What I need is the firmware configuration, leveraging COTS Ardupilot and MAV-link. At power up, the drone shall arm and launche with minimal manual intervention, besides the...

We are developing a carwash kiosk control board that will work together with our Paymore TPOS device, and we are looking for an experienced embedded hardware designer to design a production-ready PCB. This is a real commercial product that will go into mass production, therefore the design must be industrial-grade and manufacturable. The board will control a P10 LED panel (HUB75) that runs continuously 24/7, displaying countdown timers and simple messages. The system must also include Pulse+ and Pulse− inputs that can operate either as dry contact inputs or opto-isolated inputs, counting pulses and triggering system actions. Based on the detected pulses, the board must activate one of 10 independent output channels that can drive 5V or 24V signals for a defined period and then autom...

I need a robust arc-suppression circuit engineered specifically for my RF welding machine. The goal is simple and non-negotiable: stop destructive arcing before it reaches the generator or matching network, protecting the entire system from costly downtime and repairs. Key points you should know up front • Purpose: prevention of equipment damage only—operator safety circuits are handled elsewhere. • Architecture: solid-state components throughout; no relays or mechanical contacts. • Ratings: I will share the operating voltage and current range once we start, so your design must be adaptable within those limits. What I expect to receive 1. Schematic with clearly labeled protection stages (detection, quench, reset). 2. Bill of materials with manufacturer p...

I'm seeking an experienced Rockwell PLC and touchscreen programmer to automate our manufacturing processes. We already have the necessary hardware in place. Key Requirements: - Develop a touchscreen interface for: - Real-time data monitoring - Control commands - System alerts and notifications Ideal Skills and Experience: - Proficiency in Rockwell PLC programming - Experience with touchscreen interface development - Background in manufacturing automation - Ability to work with existing hardware setups

We are looking for an experienced freelancer to support us on upcoming drone development projects for our company. The work may involve design, prototyping, technical consultation, and development support depending on project requirements. We are seeking someone with strong knowledge and hands-on experience in drone/UAV systems and related technologies. Requirements: • Experience in drone/UAV design and development • Knowledge of flight controllers, motors, ESCs, GPS, batteries, and communication systems • Understanding of drone assembly, testing, and troubleshooting • Ability to suggest suitable components and technical solutions • Experience with custom drone projects is a plus • Good communication and ability to work on project-based tasks Scope of...

I need a concise Python 3 script that will run on a Raspberry Pi 5 and do the following: • Watch a single GPIO input line for the HIGH digital signal coming from my Sony camera’s built-in AI output. . The Sony camera will be pre-loaded with images of the target - in this case a plant which is detected in the target bounding box in the camera field of view. . When the target plant is encountered in bounding box of the camera field of view, the corresponding relay will activate a spray nozzle for the time the target remains in the bounding box. •The point above is achieved as soon as that digital signal is detected, drive a separate GPIO output that energises a small 5 V solenoid for as long as the target plant remains in the bounding box of the camera, then automatical...

PCB DESIGN with these or better components placement Processor & Memory Main SoC NXP iMX8M Plus — Quad Cortex-A53 1.8GHz + Cortex-M7 800MHz Safety MCU TI TMS570LS3137 — dual-core lockstep Cortex-R4F, SIL-2 certified Diag FPGA Lattice MachXO3LF-9400 — in-situ verification logic, <2ms latency RAM 4 GB LPDDR4, ECC enabled, 1600 MT/s Flash 32GB eMMC 5.1 (AES-256-XTS) + 128MB QSPI NOR boot Wireless MCU ESP32-S3 co-processor (Wi-Fi 6) Sensor Specifications Temperature PT1000 ±0.05°C (primary), DS18B20 ±0.5°C (backup), NTC (tertiary). Range: −40 to +150°C Humidity SHT45 ±1.0%RH + HDC3020 ±1.5%RH. Range: 0–100%RH, 0–85°C Pressure MS5837-02BA 0–2bar ±0.05%FS + MS5837-30BA 0–30bar (secondary) L...

I need a full architecture and layout for an advanced, multi-sensor PCB that will regulate heating, cooling and humidity inside a pharmaceutical machine. The board must interface with temperature, humidity and proximity sensors as standard, while leaving room for additional inputs such as light, pressure, water-level and high/low-voltage detectors. All sensing channels have to support automatic failure detection so the system can trigger the right alarm—heater, compressor, open door, over/under temperature, over/under voltage, pressure deviation—without user intervention. On the connectivity side I want both wired and wireless options: LAN, USB, CAN-Bus and RS-485 for plant integration, plus a wireless link for cloud dashboards. A capable processor with dedicated RAM and non-v...

Project Title: Miniature Piezo Preamp PCB (10mm) – Reverse Engineer & Redesign Project Overview I am developing a professional leak detection microphone used for plumbing diagnostics. The system uses a piezoelectric sensor to detect vibration and sound from water leaks inside pipes. I already have a working preamp circuit, but the PCB is too large for my application. I need an experienced electronics engineer to analyze the existing design and redesign it into a much smaller PCB. The new design must maintain similar electrical performance but reduce the physical size so it can be mounted directly on the piezo sensor and permanently sealed with epoxy resin inside a capsule. Primary Objectives 1. Analyze or replicate the functionality of my existing piezo preamp. 2. Redesign ...

I need a seasoned system-level engineer to build a truly standalone mobile operating system—not just an Android or iOS fork. The goal is to deliver a fully bootable image that ships with: • A visually distinctive, lightweight user interface designed from the ground up for touch • Security enhancements at kernel, system service, and application layers (hardened permissions, secure boot, encrypted storage, etc.) • A native app-store framework so third-party developers can publish, sign, and update apps over-the-air You’ll own everything from low-level board support through to UX polish, so experience with toolchains such as GCC/Clang, device tree configuration, kernel customization, and UI frameworks (Wayland, Qt, or similar) is essential. If you have previ...

I am looking for an experienced PCB designer to create a 4‑layer carrier board for a Raspberry Pi Compute Module 5 (CM5). The board integrates several existing open‑source hardware concepts into a single PCB, with limited original R&D but careful integration and cleanup. Scope of this first project - Review and consolidate existing reference schematics (I will provide open‑source designs and documentation). - Design the final schematic for: - Raspberry Pi CM5 + power supply - CAN‑based bus for a marine/industrial network (NMEA‑style) - NMEA 0183‑style serial interfaces - Connectors and I/O suitable for a small boat/embedded environment - eDP interface for an external display - PCB layout: - 4‑layer stackup with proper impedance control for eDP - Rea...

I need a fully-functioning prototype of a portable lunchbox that can actively heat food up to 60 °C and cool it down to 4 °C at the press of a touchscreen control. The enclosure should be molded primarily from food-grade plastic; please keep the overall profile compact enough to fit in a standard backpack while leaving room for the insulation, Peltier or heating elements, battery pack, control board, and a small food compartment sensor. Key functions I expect to see working on the bench: • Touchscreen interface on the lid that lets the user toggle between Heat (60 °C) and Chill (4 °C) modes, with real-time temperature read-out. • USB-C charging input feeding an internal rechargeable battery that can run at least one full heat cycle and one full cool cycle on ...

I am building a tiny GPS tracker device for my company and need an experienced PCB designer. Project Requirements: - Design schematic and PCB layout for a compact GPS tracker. - Use SIM7080G (LTE/NB-IoT with GNSS) module. - Include SIM card slot, GPS antenna connector, LiPo battery connector, and charging circuit. - Board size should be approximately 18 mm x 20 mm. Deliverables: - Complete schematic - PCB layout - Gerber files for manufacturing - Bill of Materials (BOM) - Pick and Place file (optional) Preferred Tools: KiCad, Altium Designer, or EasyEDA. Experience Required: - Experience designing IoT or GPS tracking devices - Knowledge of RF layout and antenna placement Budget: $30 – $50 (negotiable) Please share examples of previous PCB designs.

Description Of Project - HRID-AI is a low cost handheld device aimed at estimating ejection fraction using multimodal biosignals (ECG, seismocardiography, and cardiac acoustics). It uses a combination of biosensors to detect abnormalities in ECG, presence of abnormal heart sounds and their interpretation as well as usage of seismocardiographic signals to provide an estimate of Ejection Fraction. The principle has been verified through multiple studies done in reputed institutions The goal is rapid point-of-care triage for echo referral in emergency and low-resource settings in patients of Heart Failure with Reduced Ejection fraction We need your support, skills and expertise for sensor integration, embedded design, signal acquisition. Current Status- We have so far been able to dev...

We need an electronics engineer to implement a PCB design based on an existing schematic for a renewable energy monitoring project. The system measures electrical parameters from multiple sources including a solar panel, wind turbine, battery, and inverter output. The schematic already exists in PDF format and includes components such as Arduino Nano Every, MCP3903 ADC, ADS1115, WCS1600 current sensors, and HC-12 communication module. The task is mainly to follow the existing schematic, verify the design, and create a manufacturable PCB layout.

I need an experienced PCB programmer to reprogram a multi-layer PCB for a coffee maker. The board is used for a coffee maker. Required Skills and Experience: - Proficiency in reprogramming multi-layer PCBs - Experience with radio frequency (RF) applications - Knowledge in embedded systems - Familiarity with brewing settings, temperature control, timing and scheduling, and pump control functionalities