Freelancer -logo Kuinka se toimii Selaa töitä Kirjaudu sisään Rekisteröidy Ilmoita projektiProfile cover photoundefined
Seuraat nyt käyttäjää .
Virhe seurattaessa käyttäjää.
Tämä käyttäjä ei salli käyttäjien seurata häntä.
Seuraat jo tätä käyttäjää.
Jäsenyystasosi mahdollistaa vain 0 seurausta. Päivitä tästä.
Poistit käyttäjän seurannan onnistuneesti.
Virhe poistettaessa käyttäjän seurantaa.
Olet onnistuneesti suositellut käyttäjää
Virhe suositeltaessa käyttäjää.
Jokin meni vikaan. Päivitä sivu ja yritä uudelleen.
Sähköposti vahvistettu onnistuneesti.
Käyttäjän avatar
$40 USD / tunti
Maan MOROCCO lippu
casablanca, morocco
$40 USD / tunti
Kello on tällä hetkellä 4:38 ip. täällä
Liittynyt maaliskuuta 5, 2019
0 Suosittelee

Khalid K.

@kamilkhalid

monthly-level-three.svg
5,0 (4 arvostelua)
4,1
4,1
$40 USD / tunti
Maan MOROCCO lippu
casablanca, morocco
$40 USD / tunti
100 %
Suoritetut työt
100 %
Budjetin mukaisesti
100 %
Aikataulussa
20 %
Uudelleenpalkkausaste

Electronics Engineer(Hardware/Software)

Hello. Nice to meet you. As an electronic engineer, I have been working in PCB design/layout and firmware programming field for 10+ years. Here are some of the experiences that I worked ago. - Schematic and PCB Layout using Altium designer, Cadence, Eagle, and so on. - SolidWorks Enclosure, AutoCad design - Matlab simulation - Multi Layer, Flexible, High speed PCB design - Exceptional C++/C /C# programming skills. - FPGA design using Verilog/VHDL (Xilinx ISE/XPS/SDK/Vivado, Altera Quartus, iCECube) - ARM, DSP, MCUs, Arduino experience. - Arm cores: ATSAM, STM32, PIC32, A13, FreeScale, MSP, NXP - MPU: Pic16F, Pic18F, Pic33F, Atmega8,16,128,32,8051,8951,8052,80251 - Single board computer: Raspbery pi, Beaglebone, NanoPi - Strong with UART, I2C, SPI, BLE,BT, GSM/GPRS/GPS, xBee, ZigBee. - Especially full experience for BLE HM10, HC05, ESP32, DA14580, nRF52832, 52840, BlueNRG, Once you hire me, expected me to help your business like I 'm growing it as my own. I would love to hear from you. Kindness regards.
Freelancer Electronics Engineers Morocco

Ota yhteyttä käyttäjään Khalid K. työhösi liittyen

Kirjaudu sisään keskustellaksesi yksityiskohdista chatin välityksellä.

Portfoliokohteet

The Display Unit (DU) is a LCD display which conveys state of a systems status for an operator to monitor the system’s operation and make adjustments as required. It accepts data Bytes in ASCI Hexadecimal format from a system host computer using an Ethernet input and constructs messages for the LCD display by converting the hex information into characters as defined by a set of Lookup Tables. Character generation,
Display RAM addressing, Cursor Scrolling, Blanking and Highlighting are all included.
Character tables can be changed over the Ethernet input by the host computer using PSPC. Image intensity is controlled by varying the PWM driver backlight duty cycle with the DU MCU output set by the input data.
Display Unit PCD
The Display Unit (DU) is a LCD display which conveys state of a systems status for an operator to monitor the system’s operation and make adjustments as required. It accepts data Bytes in ASCI Hexadecimal format from a system host computer using an Ethernet input and constructs messages for the LCD display by converting the hex information into characters as defined by a set of Lookup Tables. Character generation,
Display RAM addressing, Cursor Scrolling, Blanking and Highlighting are all included.
Character tables can be changed over the Ethernet input by the host computer using PSPC. Image intensity is controlled by varying the PWM driver backlight duty cycle with the DU MCU output set by the input data.
Display Unit PCD
The Display Unit (DU) is a LCD display which conveys state of a systems status for an operator to monitor the system’s operation and make adjustments as required. It accepts data Bytes in ASCI Hexadecimal format from a system host computer using an Ethernet input and constructs messages for the LCD display by converting the hex information into characters as defined by a set of Lookup Tables. Character generation,
Display RAM addressing, Cursor Scrolling, Blanking and Highlighting are all included.
Character tables can be changed over the Ethernet input by the host computer using PSPC. Image intensity is controlled by varying the PWM driver backlight duty cycle with the DU MCU output set by the input data.
Display Unit PCD
LED RF circuit- the leds need to be driven at 4.5 volts and 5050  type - RGB 
Send RF off command to all Leds and devices.
The BT IC need to be stereo -left CHannel to the Speaker,right to pad connector or the 2nd PCB to connect. 
Light Switch/Buton  - need track to Pad to connect 2nd PCB. 
the Button will be to turn of or reset the LEDS 
Sequence will be press Light Button. 
Button On power - powers on Both PCB, Sends Power to Connector for extra PCB.
BT LED Speaker Board
LED RF circuit- the leds need to be driven at 4.5 volts and 5050  type - RGB 
Send RF off command to all Leds and devices.
The BT IC need to be stereo -left CHannel to the Speaker,right to pad connector or the 2nd PCB to connect. 
Light Switch/Buton  - need track to Pad to connect 2nd PCB. 
the Button will be to turn of or reset the LEDS 
Sequence will be press Light Button. 
Button On power - powers on Both PCB, Sends Power to Connector for extra PCB.
BT LED Speaker Board
LED RF circuit- the leds need to be driven at 4.5 volts and 5050  type - RGB 
Send RF off command to all Leds and devices.
The BT IC need to be stereo -left CHannel to the Speaker,right to pad connector or the 2nd PCB to connect. 
Light Switch/Buton  - need track to Pad to connect 2nd PCB. 
the Button will be to turn of or reset the LEDS 
Sequence will be press Light Button. 
Button On power - powers on Both PCB, Sends Power to Connector for extra PCB.
BT LED Speaker Board
- CM4 connector
- Mini PCI-E socket with SIM card holder
- 2 x Power input (~10 to ~ 30 Volt). State of both connected to GPIO pins as signal (so reduced to some ~2 Volts)
- 2 x I2C exposed
- Battery charging controller. The main power reduced to 5 V, then connected through the battery charging controller back to the board.
- MicroSD card socket.
- SPI exposed
- Few (~5) additional GPIO pins exposed.
CM4 Carrier Board
- CM4 connector
- Mini PCI-E socket with SIM card holder
- 2 x Power input (~10 to ~ 30 Volt). State of both connected to GPIO pins as signal (so reduced to some ~2 Volts)
- 2 x I2C exposed
- Battery charging controller. The main power reduced to 5 V, then connected through the battery charging controller back to the board.
- MicroSD card socket.
- SPI exposed
- Few (~5) additional GPIO pins exposed.
CM4 Carrier Board
The schematic below is from the receiver (light fitting end).  Actually there are 7 LED drivers inside the light fitting to control Red, Green Blue and 4 White channels of the light.  Each LED driver circuit is bypassed with the same circuit shown below, so we have 7 drivers all in parallel from Vin.  When installed in the venue, there will be 4 light fittings on the line, so 5 devices communicating, and 28 LED drivers.
LED Driver
The schematic below is from the receiver (light fitting end).  Actually there are 7 LED drivers inside the light fitting to control Red, Green Blue and 4 White channels of the light.  Each LED driver circuit is bypassed with the same circuit shown below, so we have 7 drivers all in parallel from Vin.  When installed in the venue, there will be 4 light fittings on the line, so 5 devices communicating, and 28 LED drivers.
LED Driver
Input offers full galvanic isolation between the PV string and the DC bus. The SPOT is compatible with any PV string voltage including 600, 1000 and 1500 volt PV strings.
DC-DC Optimizer, Solar storage

Arvostelut

Muutokset tallennettu
Näytetään 1 - 4 / 4 arvostelua
Suodata arvosteluja: 5,0
$250,00 USD
Khalid had a very solid understanding of the project and came up with the schematic quickly. With just a few tweaks resulting from the dialog between us, he completed the project in substantially less time than allotted. We have several projects in front of us, and I'm happy to have connected with Khalid.
Electronics Electrical Engineering Circuit Design
Käyttäjän avatar
Maan  lippu Brian W. @bri4eng2
4 kuukautta sitten
5,0
€500,00 EUR
Delivered very fast. Very good communication. We are definitely going to work together in the future. Great job
Electronics Microcontroller Electrical Engineering PCB Layout Circuit Design
N
Maan  lippu Alina B. @NeoFox2000
4 kuukautta sitten
5,0
$300,00 CAD
Excellent work, i would definitely recommend
Electronics Microcontroller Software Architecture PCB Layout
+1 enemmän
Käyttäjän avatar
Maan  lippu Aleksandar T. @aleksandart450
5 kuukautta sitten
5,0
$100,00 USD
Delivered on time. Very serious and professional. Friendly as well. Great communication.
Electronics Microcontroller Electrical Engineering PCB Layout Circuit Design
Käyttäjän avatar
Maan  lippu Aleksandar T. @aleksandart450
6 kuukautta sitten

Koulutus

M.Sc Electronic Engineer(Hardware, Embedded System, Software)

Université Hassan II Aïn Chock de Casablanca, Morocco 2010 - 2013
(3 vuotta)

Ota yhteyttä käyttäjään Khalid K. työhösi liittyen

Kirjaudu sisään keskustellaksesi yksityiskohdista chatin välityksellä.

Varmennukset

Suositeltu freelanceri
Henkilöllisyys varmennettu
Maksutapa varmennettu
Puhelinnumero varmennettu
Sähköpostiosoite varmennettu
Facebook yhdistetty

Parhaat taidot

Electronics 4 Circuit Design 4 Microcontroller 3 Electrical Engineering 3 PCB Layout 3

Selaa vastaavia freelancereita

Electronics Engineers in Morocco
Electronics Engineers
Circuit Designers
Microcontroller Developers

Selaa vastaavia näyteikkunoita

Electronics
Circuit Design
Microcontroller
Electrical Engineering
Edellinen käyttäjä
Seuraava käyttäjä
Kutsu lähetetty onnistuneesti!
Rekisteröitynyttä käyttäjää Ilmoitettua työtä yhteensä
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2023 Freelancer Technology Pty Limited (ACN 142 189 759)
Ladataan esikatselua
Lupa myönnetty Geolocation.
Kirjautumisistuntosi on vanhentunut ja sinut on kirjattu ulos. Kirjaudu uudelleen sisään.