Verilog Code for DE0-Nano board


Create a project about a 128x3 (128 words, with 3 bits at each word) single- port RAM in Verilog, simulate the design, and load

it into the Cyclone IV chip on the DE0-Nano board. The design uses two push-buttons and one DIP switch as inputs.

One side of the DIP switch clears the memory address (not the memory contents).

The depressing of the first push-button indicates a memory write action. In this case, the 50 MHz clock signal available on the FPGA board is used as an input to increase the RAM address. The 3-bit data value written to a memory location at an address should represent the number of ones in the 7 address bits. For example, a value of 011 (=3) should be written to the location with an address of 1000011.

Once the first push-button is released, the memory read is in action. In this case, the 3-bit data stored at the current address are to be displayed using three LEDs. The releasing of the second push-button increases the memory address by one.

In addition, connect the 5 least significant address bits to 5 LEDs. Write a DO file for the simulation. The simulation needs to demonstrate the writing to the RAM followed by reading from the RAM, each involving a few RAM locations. You need

to do the following prior to compilation:

Generate a Verilog file for the single-port RAM by

using “the IP Catalog” of Quartus Prime. (Use “On Chip Memory” which is with in “Installed IP




Basic Functions”.)

Add the Verilog file for the RAM to the project.

Instantiate a memory component in the design.

For the address control, you must instantiate two copies of a 7-bit up counter (modified from the 3-bit from Assignment 2). One is for generating read addresses and the other for write addresses. A multiplexer should be used to connect the right address to the RAM input.

For the simulation you will need to include the

altera_mf_verlibrary. This can be done in ModelSim-Altera using the “Libraries” tab within the “Start

Simulation” window.


Create a project about the on-board 3-D accelerometer in Verilog, and load it into the Cyclone IV chip on the DE0-Nano board. Th

e design uses one push-button and one LED.

Pressing down the push-button turns off the LED.

The LED is turned on when the board is suddenly mov

ed. (The degree/direction of movement is of your choice, but should be reasonable.)

Demonstrate the project. There is no need for simu


How it can be done:

On the DE0-Nano board CD, which is available on the

course Pilot website,

copy the folder demonstration/DE0_NANO_GSensor to t

he PC hard drive. From the

hard drive folder, you may use Quartus Prime to ope

n an existing project file,

compile the project, and program the board. There

is no need to assign pins since

that has already been done. Study the code. (On P

ilot, under FPGA/Verilog HDL

Sample Codes/GSensor-Demo-Code-Listing, there is a

PDF file, named “Using the

3D Accelerometer”, that describes the code.)

DE0_NANO_G_Sensor.v contains the

top-level module of the project.

Taidot: Verilog / VHDL, Mikrocontroller, FPGA, elektroniikka, sähkötekniikka

Näytä lisää: hex ascii conversion verilog code, verilog code parking lot project, elgg job board module, verilog code ascii codes, embedded board module openvpn, message board module zen cart, peak detector verilog code, drupal message board module, online verilog code project, verilog code freelance, verilog code transfer packet modules, discussion board module sugarcrm, verilog code, binary decimal verilog code, verilog code pci, verilog code board game

Tietoa työnantajasta:
( 0 arvostelua ) Fairborn, United States

Projektin tunnus: #21854960

Myönnetty käyttäjälle:


Hello, thank you for your job posting. I am a senior device developer. I have plenty of experience in firmware development and micro-controller developments. I can write the firmware based on Arduino, Raspberry Pi, Pic Lisää

$50 USD 1 päivässä
(9 Arvostelua)