Freelance Technical Trainer

$250-750 USD

Suljettu

Julkaistu

yli 11 vuotta sitten

$250-750 USD

Maksettu toimituksen yhteydessä

Looking for freelance trainer in the field of Process Automation | Electrical | Mechanical | Instrumentation Process Automation Programmable Logic Controllers (PLC) Allen Bradley : PLC 5 / Micrologix series / SLC Series / ControlLogix Siemens : S5100U / Step 7 200 / Step 7 300 / Step 7 400 Schneider Electric : Modicon TSX Micro / Quantum / Premium / M340 GE Fanuc : 90 – 30 Series / VersaMax Omron : CQM Series Mitsubishi : Q Series & Fx Series Messung Systems : Nextgen 5000 ABB : AC 500 & Advance Distributed Control System (DCS) Emerson : Delta V M40 Controller (Only in India) Yokogawa : CS 3000 ABB : Freelance AC800F & AC700F ABB : ABB 800xA (AC 800M) Honeywell : Experion C2000 Siemens : PCS 7 Allen Bradley : ControlLogix systems Supervisory Control & Data Acquisition (SCADA) Allen Bradley : RSView 32 Siemens : WinCC GE Fanuc : Cimplicity & Intellution FIX Dmacs Others make : WonderWare InTouch, Citect, Aspic. SCADA Systems for the Petroleum Industry SCADA/HMI System, Remote Terminal (RTU), and Field Instruments Supervisory Control & Data Acquisition (SCADA) OP / TP Allen Bradley : PanelBuilder32 / RsView SE & ME / Factory Talk Siemens : WinCC Flexible / ProTool Schneider : Magelis XBT AC – Drives Allen Bradley : Powerflex Siemens : MicroMaster Schneider : Altivar Others make : ABB | Yaskawa | Emerson Control Technique | Delta Electrical Basic Electrical Systems and Electrical Safety Electrical Maintenance, Testing, Inspection and Risk Assessments Virtual frequency drives – VFD Motor management & VFD Basic Electrical Systems and Electrical Safety Modern Electrical Power System Power Quality Analysis and Analyzers Single Line Diagram & Troubleshooting Control Circuit Developing an Effective Safety Culture Electrical Installation & Maintenance Electrical Maintenance, Testing, Inspection and Risk Assessment Relay Setting and Co-ordination L V Switchgears Logic Building Using Contactors and Relays Transformer Electrical Losses Electrical Safety Electrical Training for Technician & Fresh graduate Mechanical Mechanical Drawing Reading Basic Mechanics Maintenance --A to Z of best practices Lubricants and Lubrication Power Transmission Equipment Bearings -Maintenance, Troubleshooting & Repair Pumps -Maintenance, Troubleshooting & Repair Gear Box Systems– Theory, Practice and Maintenance Hydraulic Systems Hydraulic & Electro Hydraulic Pneumatic Systems Electro Pneumatic systems– Theory, Practice & Trouble-shooting Alignment Theory and Practice Compressor & Blower -Maintenance & Repair Mechanical Seals -Maintenance & Repair Valve Repair -Maintenance & Repair Steam Engineering Air Engineering Thermic (Heat transfer) fluid heating systems Advanced Mechatronic Systems Diesel Engine power plants Boiler Management Air conditioning and refrigeration systems Diesel Generator (DG) Maintenance & Troubleshooting Instrumentation Fundamentals of Industrial Measurement Pressure | Flow | Temperature | Level Foundation Field bus Instrumentation & Calibration Training Process Control & Loop Tuning HAZARDOUS AREA INSTRUMENTATION GAS MONITORS Fire & Gas detection systems Control System Automation

Chemical Engineering

Electrical Engineering

Instrumentation

Mechanical Engineering

PLC & SCADA

Projektin tunnus (ID): 2556451

Tietoa projektista

11 ehdotukset

Etäprojekti

Aktiivinen 11 vuotta sitten

Haluatko ansaita rahaa?

Sähköpostiosoite

Freelancerin tarjouskilpailun edut

Aseta budjettisi ja aikataulu

Saa maksu työstäsi

Kuvaile ehdotustasi

Rekisteröinti ja töihin tarjoaminen on ilmaista

11 freelancerit tarjoavat keskimäärin $550 USD tätä projektia

@bchandra1955

Professional automation engineer here.

$999 USD 15 päivässä

4,3

(17 arvostelua)

5,0

@ranscfd

Expert Trainer Mechanical

$750 USD 10 päivässä

4,8

(9 arvostelua)

4,4

@tjtj

Hello, We have got fair bit of expertise in automation industry. More details are sent to your message box.

$750 USD 25 päivässä

4,8

(5 arvostelua)

3,9

@mikiitbhu

I belong to Electronics and Instrumentation Engineering and available for 2 Hours daily.

$600 USD 30 päivässä

0,0

(0 arvostelua)

0,0

@flomanea

Hello...I like your job description and I will like to help you. The money is not very imoprtant in this project, is very important the good job and profesional satisfaction. I am design engineer in automotive industry and I can help you, I have a lot of experience in CAD-CAM-CAE products, and freelancer collaboration also. I am approved Autodesk trainer, I have validate for Autodesk apps, like AUtocad, Inventor, Vault. I have a good experience in Unigraphics NX (I worked for Fiat), Catia V4 and V5 (I worked for Renault), Pro/E Creo (I working for Toro Company). Please, see my profile

$250 USD 20 päivässä

0,0

(0 arvostelua)

0,0

@onerode

Professor... I can handle all the topics mentioned by you.

$500 USD 6 päivässä

0,0

(0 arvostelua)

0,0

@emildancu

I have necessary skills to be a good trainer in the electricall field for your project.

$500 USD 20 päivässä

0,0

(0 arvostelua)

0,0

@khadorik

I have experience in the automation field of Process Automation - Siemens, Mitsubishi, Wago, Omron, iFix, InTouch, Citect. I can work in this project 1-2 hour daily. Send me more information about the job.

$500 USD 20 päivässä