Käynnissä

PCB and firmware IR circuit

I am looking for PCB design, and the Gerber files to hand to prototypers.

the circuit will use for a local textile machines

*Components will include PCB, IR (Emmitor- detector), a small microprocessor, power transistor to drive a relay, a dual color LED, and the circuit will communicate with a mega Arduino via I2C protocol.

*small program to operate the PCB.

*the body form will be a whole disk with 30 mm out diameter the hole dia is 10mm and with a good design.

1- we want a PCB circuit with 30 mm out diameter and a central hole of 10 mm

2- this circuit have at one face IR transmitter and IR receiver and BI-LED

3- this circuit will have at another side the other component

the circuit work is to:

1- work independently and communicate with the main circuit in some times and in some textile machines may we use only the circuit without the main unit

2- use an encrypted IR beam to avoid the outer confusion

3- when the IR beam cuts for time T1 the relay must actuate for time T2

4- when the IR cut for time T3 the relay must actuate for time T4

5- T1, T2, T3, T4 is adjustable by program

6- our circuit can tell the main circuit via I2C protocol that it is actuate or not

7- the main circuit can command our circuit via I2C protocol to actuate the relay for time T2 or T4

8-The Bi-LED doesn't connect to any another component of the circuit and have its own socket because it will work with another circuit

9- the sockets have to arranged as in diagram

two I2C pins separately

four pins in another socket the first +v second NO third NC fourth 0v

the Bi-LED must locate as close as possable to the central hole

the IR components must locate at the ends of the circuit circle diameter facing each other

Please quote for just schematic and also PCB layout. Looking to start immediately.

you have to know:

1- your mission is to design draw and program the circuit with its library have to put on mega Arduino

2- the protocol is I2C

3- every circuit will put on one shuttle work line and many circuits will attach to one mega Arduino to work in one textile machine

4- we can provide the textile machine with an Arduino or only with our circuits

and work normally and independently

T1 & T2 is between 0-1 second with a 0.1 step

T3 and T4 is between 1-5 seconds with 0.5 second step

we can adjust T1, T2, T3, T4 by the Arduino

if your work does not meet one of the conditions we will be

Thanks!

Skills: PCB Layout, Electronics, Product Design, Electrical Engineering, Schematics

Taidot: Piirilevyn asettelu, elektroniikka, Mikrocontroller, sähkötekniikka, Piirisuunnittelu

Näytä lisää: pcb layout supply circuit, running pcb projects electronics circuit diag detailed information components, pcb firmware, pcb layout inverter circuit, pcb battery protection circuit, how can i find a designer to sign my t shirts, i have 3 very simple webpage designs but i have lost the psd for them i need someone to redo it and send me the psd file, i have a company selling organic handmade turkish towels the name is (yknot) as of a knotted rope, i have a company selling organic handmade turkish towels the name is yknot as of a knotted rope, i have around 1000-1100 product images that i need edited to show a pure white background the products are mainly jewelry suppli, i have around 10001100 product images that i need edited to show a pure white background the products are mainly jewelry supplie, i need a design for a bottle label this is for a vitamin water and it comes in 4 flavours it is quite simple as i already have a, i need a graphic designer for a t shirt using cafe press, i need a graphic designer for a t shirt, how do i tell a promoter that i m a dj i need a gig, logo design where i tell people what i want and they bid and create, looking for a saying regarding marketing communication which goes along this line if i tell you i am beautiful then it is advert, PCB design and circuit design

Tietoa työnantajasta:
( 1 arvostelu ) Mersin, Turkey

Projektin tunnus: #23890673

Myönnetty käyttäjälle:

etalhak

Merhaba, Ben elektronik ve haberleşme mühendisiyim. Daha önce buna benzer bir çok devre tasarladım ve I2C gibi haberleşme protokollerini birçok defa kullandım. Yukarıda bahsettiğiniz projeyi çok rahat bir şekilde yapab Lisää

$100 USD 7 päivässä
(0 Arvostelua)
0.0

22 freelanceria on tarjonnut keskimäärin 197$ tähän työhön

ahmedmohamed85

Dear sir I have more than 10 years experience in embedded systems design, please check my profile, also please message me so that we can discuss Best regards

$200 USD 7 päivässä
(245 arvostelua)
7.3
Anthony989

Hello, I am Anthony from Sri lanka. I have 7 years of experience in the field of electronics. Currently I am working as a full time freelancer and I have state of the art electronic lab. Why you should h Lisää

$140 USD 7 päivässä
(59 arvostelua)
6.5
amelectronics

Hello sir, I have experience in designing electronics circuits and can program all kinds of microcontrollers. You can discuss your project with me in chat and we can move on right away. Thank you.

$150 USD 7 päivässä
(41 arvostelua)
6.6
mos3d

Greeting There , I could absolutely help you with your PCB/PCBA project i am Auto-desk ACI certified on Eagle CAD , i am sure that i the PERFECT contractor for your project . below sample of my board design ( PCB AND Lisää

$300 USD 5 päivässä
(41 arvostelua)
6.1
tifoda

Hello. Im designing different electronics devices, mostly based on avr, arm MCUs and boards with them like arduino, stm-discovery etc. (autopromotion^)) Hi. Schematic and pcb design are only half of work here. Least Lisää

$200 USD 7 päivässä
(46 arvostelua)
5.8
jitendrabaraiya

I have more than 8 years experience in PCB design with eagle and Altium design software with firmware development . so I can do your job within a time limit with your satisfaction.

$500 USD 30 päivässä
(6 arvostelua)
4.6
intellisenseIN

Hi there, We can design the Schematic & PCB layout and can start work immediately. We came across with your requirements very carefully. My name is Jaspreet & I'm part of larger embedded hardware and firmware developm Lisää

$350 USD 10 päivässä
(4 arvostelua)
4.4
danish2051

I am specialist in development and interfacing between Android application and arduino board. hardware designing for embedded hardware. software development for embedded hardware. Home automation. Controlling hardware Lisää

$177 USD 5 päivässä
(11 arvostelua)
3.7
malindu2002abeys

Hello, I am confident that I can complete your project perfectly. I'am experienced in, Digital and Analog electronics. Arduino , ESP32, ESP8266, PIC , AVR, ARM, 8051, STM32 programming PCB designing C , C++ , Java , P Lisää

$50 USD 4 päivässä
(7 arvostelua)
3.2
gsa5b06f37877085

Hello, I am an electronic engineer and electromechanical technical. I work in an electrical testing laboratory, under international standards, I have been working here for more than two years I have more than 5 years Lisää

$140 USD 7 päivässä
(3 arvostelua)
3.5
Gerrard97

We are a team of Electrical and Electronics engineers and we are Excellent in the following areas: • PCB Designing-Proteus, Eagle. • Python • Embedded C Programming. • VHDL/Verilog • Microcontroller like Arduino, R Lisää

$250 USD 7 päivässä
(3 arvostelua)
2.7
andyf1

Good day! I'm an embedded engineer with experience with pcb and communication between microcontrollers via I2C. I’m interested in working on your project. Please contact me so that we can discuss the details of your Lisää

$222 USD 7 päivässä
(5 arvostelua)
2.3
youcefR000T

hello I m electronic engineer I have a great experience in schematics and pcb design since that what I am doing with my company, I usually use proteus and easyEda . don't hesitate to contact me

$140 USD 7 päivässä
(1 arvostelu)
1.3
chandupneja

I am confident that I can do this. I have an experience of 20 years in hardware R&D. If you talk/chat with me on this, I would like to close some points before accepting the project. Accordingly, the timeline and price Lisää

$300 USD 20 päivässä
(1 arvostelu)
0.6
Devendhiran17

Hello, I am currently working as a hardware design engineer for the past eight years. I read your detailed Requirements and felt that definetely I would be one of the suitable person to take up this project. I have Lisää

$250 USD 60 päivässä
(0 arvostelua)
0.4
johnEngineer132

Dear Sir. I have seen your description very carefully and posting to you my idea. I have no job history but have many experiences about your job. If you give me a chance to interview, I'll explain in more detail and I' Lisää

$140 USD 7 päivässä
(0 arvostelua)
0.0
GoodCooper

Hello! Nice to meet you. I have 5+ years experience in designing electronics circuits and programming all kinds of microcontrollers including Arduino, Raspberry PI, etc. Designing printed circuit board (PCB) layout wit Lisää

$150 USD 5 päivässä
(0 arvostelua)
0.0
ahmedreda2962003

Hello sir, have read your project very well and I'll help you to do anything. I can do that if you have the circuit and want Gerber file as you said please connect me with full details

$30 USD 1 päivässä
(0 arvostelua)
0.3
csheshnath

Hi, I have more than 4 years experience in the filed of PCB design including schematic,layout gerber and [login to view URL] i can complete your work within 5days with high preority. thank you Sheshnath

$190 USD 5 päivässä
(0 arvostelua)
0.0
AmirLatif786

I have gone through your project and it matches my expertise. I can assure you that if selected, I will complete the job within 2 weeks.I am a Electrical Engineer please provide me your circuit [login to view URL] interested, o Lisää

$150 USD 4 päivässä
(0 arvostelua)
0.0