Suoritettu

Modify Existing Raspberry Pi Compute Module 4 io Breakout Board (KIKAD 6 nightly build required ) Shematic + Board [login to view URL] only bid Actual Amounts

Modify Compute Module 4 iO Board

I would like to change the Compute Module 4 io board to suit my project . Design must be done in Kikad 6 ( nightly build required as described

Here: [login to view URL])

Designfiles can be found here :

[login to view URL]

[login to view URL]

Delete the following parts from the current design :

• GPIO Header

• Remove 2nd DSI connector

• Remove 2nd HDMI connector

• Remove SD Card reader

• Remove both Camera connectors

• Remove GPIO Header

• Remove PCI Express

• Remove POE Header

• Power Supply Barrel Jack

Add the following to the board :

• Main Breakout Connector 34 Way Connector (Amp Superseal 2-6447232-3)

• 2 CAN bus Modules (Adapt the schematic from the PI Hat in the files to suit the Pi4 Compute module )

CAN High and Low for both modules should be broken out to the main connector described below The jumpers (J1 and J2 ) to set the 120 Ohm resistor active should be each broken out to the main 34 pin connector so they can be set by bridging 2 pins on the main 34 pin connector

• Add a connector on the board to directly plugin this Neo M8N GPS board ( GND 3.3V RX Tx)

• Add a 8 Channel ADC (MCP 3008) so I can read in Analog Voltages 0-5V ( Break out the inputs to 34 pin main connector ) Also add overvoltage protection for the inputs

• Add a circuit so I can read in 6 digital inputs ( Based of 12 V 12v on 0v off add overvolt protection ) ( Break out the inputs to 34 pin main connector and )

• Modify the Power supply circuit in the following manner :

Input comes from a 12 V Car battery (Permanent 12 V and Switched 12 v via ignition coming from 34 Pin main connector )

There needs to be a voltage stabilisation to prevent having Power Cuts when the voltage drops during cranking of the Engine.

Have 2x 12 V inputs . One is permanent 12 V the other one is a switched input from the Ignition .

The Board should be powerd via the permanent 12 V but only when ignition is on . When there are 12 v on the ignition wire a GPIO pin should be set to high and power should be supplied via the Permanent 12 V input . When the ignition wire is off . the GPIO should go to low and the 12 V Power from the permanent 12 V should be cut with a 10 seconds time delay

( this way I can monitor the GPIO state via software and trigger a safe shutdown to prevent file system corruption )

• Add 4 connectors on the board connected to 4 GPIO pins ( 2 pin connectors with the other pin connected to 3.3V so I can connect some switches to those connectors to switch pins to switch GPIO to while pressing )

Add one big central 34 pin Connector with the following inputs outputs

Connector Type : Amp Superseal 2-6447232-3 :

• 12 V Switched input ( 12 V from ignition )

• 12 V Permanent input (12V from Car battery)

• 1x Main Ground

• CAN 1 High

• CAN 1 Low

• CAN 2 High

• CAN 2 Low

• 2 pins that can be bridged to close the connection of the 120 Ohm Termination ResistorCAN1

• 2 pins that can be bridged to close the connection of the 120 Ohm Termination ResistorCAN2

• 12 V Switched input ( 12 V from ignition )

• 12 V Permanent input (12V from Car battery)

• 1x Ground

• 8x Analog 0-5V inputs ( with some protection in case 12 V is accidentally applied )

• 1 communal ground for Analog inputs

• 6x Digital inputs ( 12 V inputs that can set the 6 differen GPIO’s to high (need to be converted to 3.3 V)

• 1 x SDL out

• 1x SDA out

• 1 x 5V out

• 1x Ground out

Taidot: Piirilevyn asettelu, Mikrocontroller, Piirisuunnittelu

Näytä lisää: project bid interior design singapore, bid graphic design stationary, design works required, raspberry pi compute module development kit, rpi compute module io board schematic, raspberry pi compute module case, raspberry pi compute module display, rpi compute schematic, compute module io board v3 schematics, raspberry pi i/o board, raspberry pi display adapter board schematic, bid image design, bid web design projects, bid graphic design print job, bid graphic design work churches, bid cad design, hot bid freelance design projects free, bid circuit design, logo designers bid logo design, creative freelance bid web design

Tietoa työnantajasta:
( 4 arvostelua ) Pretoria, Germany

Projektin tunnus: #27872284

Myönnetty käyttäjälle:

(35 Arvostelua)
6.1

4 freelanceria on tarjonnut keskimäärin $533 tähän työhön

Andrii0125

Hi, I have read your project description carefully, so I am very interesting in your project. I will finish your board design in a short time perfectly. Best regards, Andrii.

$1500 USD 7 päivässä
(16 arvostelua)
5.2
HarimohanG

Best Raspberry Pi Design Expert at your service! Dear Client, I have seen the images, pdf and could do it for you I can change the Compute Module 4 IO board to suit your project After going through your project details Lisää

$180 USD 2 päivässä
(2 arvostelua)
4.4
fabienbenoit1984

Hello! I'd like to help with an embedded product. I'll provide system's design document with ready-to-use open source components and time estimates for a development. Thanks.

$200 USD 7 päivässä
(0 arvostelua)
0.0