Find Jobs
Hire Freelancers

Firmware designer

₹12500-37500 INR

Suljettu
Julkaistu yli vuosi sitten

₹12500-37500 INR

Maksettu toimituksen yhteydessä
We have a working PCB with unknown firmware, we need to replicate the firmware.
Projektin tunnus (ID): 34307483

Tietoa projektista

13 ehdotukset
Etäprojekti
Aktiivinen 2 vuotta sitten

Haluatko ansaita rahaa?

Freelancerin tarjouskilpailun edut

Aseta budjettisi ja aikataulu
Saa maksu työstäsi
Kuvaile ehdotustasi
Rekisteröinti ja töihin tarjoaminen on ilmaista
13 freelancerit tarjoavat keskimäärin ₹88 365 INR tätä projektia
Käyttäjän avatar
Hello, I've good experience programming and reverse engineering, please send me more details about your board and firmware. Let me know if you have any questions.
₹25 000 INR 7 päivässä
5,0 (20 arvostelua)
6,2
6,2
Käyttäjän avatar
Which is the processor, do you have circuit diagram, please write to me about the functionality and logic of the board.
₹25 000 INR 7 päivässä
5,0 (44 arvostelua)
5,2
5,2
Käyttäjän avatar
Hello, I am an electronics and telecommunication engineer and my major is wireless systems' design. I am experienced in hardware and embedded systems' design. I have designed/printed/tested many PCBs and I am quite experienced with RF design such as designing antennas, matching networks(distributed/lumped elements), filters(distributed/lumped elements), power amplifiers, dividers, feed networks, differential pairs/signals, EMI, clearance areas, shielding for EMI, conducted interference, common mode, etc, LVD, high speed data communication. I have checked your requirements I am quite sure that I can help you with your project. Just give me all the details and I will do my best to help you. Best regards
₹25 000 INR 7 päivässä
4,7 (50 arvostelua)
5,6
5,6
Käyttäjän avatar
Good day, I can help to replicate the firmware in a quality and timely manner. Please share me more details about this project. I would like to have a thorough discussion on this project as there are certain suggestions from my side After dedicating more than 30 years to the electronics design and development, I am passionate in designing the best products Technology wise I have worked on all the latest technologies like GSM, 5G, Lora etc. And have worked on more than 20 design tools for designing and simulation purpose Some of the generic queries from my side are: 1. What is the application of this product? 2. What will be the ambient temperature of this product? 3. What are the mechanical constraints to be taken care of? If you are someone who wants to benefit from my experience just message me Hi and I shall be there for you Regards Hari Mohan Engineering for one is magic for others
₹37 500 INR 7 päivässä
5,0 (5 arvostelua)
5,2
5,2
Käyttäjän avatar
I have more than 9 years experience in embedded PC design and firmware development with full prototype . So I can do your job within a time limit with your satisfaction.
₹789 630 INR 60 päivässä
4,8 (8 arvostelua)
4,9
4,9
Käyttäjän avatar
Hello; I am working as a research and development manager in a private company. I have more than 5 years of experience in embedded systems hardware. I am an expert in Altium, KiCad programs. I am also proficient in other drawing programs. I have read and understood your project. I can design the pcb on the platform you want, taking into account the sensitive signal transitions, in accordance with the international pcb rules. Please write to me for details.
₹25 000 INR 6 päivässä
4,6 (8 arvostelua)
4,4
4,4
Käyttäjän avatar
Hey there! I can help you in replicating your device firmware as per your requirements. Have a look at my portfolio, I have experience in designing PCBs and writing firmware. I have used Arduino, ESP32, ESP8266, AVR, and PIC microcontrollers before. Message me and I'll clear your doubts. Looking forward to work with you!
₹35 500 INR 7 päivässä
5,0 (21 arvostelua)
3,6
3,6
Käyttäjän avatar
Replicating a firmware sounds a solution, but may not be efficient in your case. let me know what are the tasks of your system and actual schematics theni would propose the switch on a new MCU with dedicated firmware that will do same job. looking foward to your specification so i would make the adequate bid. Look forward earing from you cheers.
₹60 000 INR 45 päivässä
0,0 (0 arvostelua)
0,0
0,0
Käyttäjän avatar
Hello How are you doing My suggestion is instead of replicating unknown Firmware because the manufacturer might have a custom made chip or chips for their projects will be impossible to replicate. tell me what the device does? what are the inputs and outputs? examples inputs buttons, sensors: humidity, temperature, speed (Tachometer), magnetic (Hall effect), Light, rotary, keypads. outputs: Motors, Valves, Relays, LCDs, LEDs, LEDs Displays etc... will be much simpler to do a custom Electronic Board and it's Firmware I will give you all source files of firmware and electronic board schematics
₹13 611,11 INR 3 päivässä
0,0 (0 arvostelua)
0,0
0,0
Käyttäjän avatar
Hi there, I have read your project description and I am confident about your project I can do perfectly. Please leave a message on my chat so we can discuss the budget and deadline of the project. Thanks. regard , Younes
₹12 500 INR 2 päivässä
0,0 (0 arvostelua)
0,0
0,0

Tietoja asiakkaasta

Maan INDIA lippu
Delhi, India
0,0
0
Liittynyt elok. 11, 2019

Asiakkaan vahvistus

Muita töitä tältä asiakkaalta

MCOS design
₹12500-37500 INR
Kiitos! Olemme lähettäneet sinulle sähköpostitse linkin, jolla voit lunastaa ilmaisen krediittisi.
Jotain meni pieleen lähetettäessä sähköpostiasi. Yritä uudelleen.
Rekisteröitynyttä käyttäjää Ilmoitettua työtä yhteensä
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Ladataan esikatselua
Lupa myönnetty Geolocation.
Kirjautumisistuntosi on vanhentunut ja sinut on kirjattu ulos. Kirjaudu uudelleen sisään.