Suoritettu

PCB and Schematic design

This project is a fully of typicals designs where usign a microcontroller, pwm output with 2nd order rc lowpass filter this signal go to op amp non inverted amplifier configuration, the op amp output must be boosted (with bjt or jfet) I need 100ma minimun current in the 0-10 volts output.

Requirements

• 2 pwm outputs

• 2 RC 2nd order lowpass filters

• 2 non inverterted op amp configuration, output must be boosted (bjt o jfet)

• 2 relays SPST (with transistor bjt and protection diode)

• 1 relay SPDT (using 2 relays SPST with transistor bjt and protection diode)

• 2 RS485 (using pcb module)

• 2 GIOP

• 4 Leds

• 4 push buttons

The time of realization is 7 to 10 days, the design software that you can use is Eagle or Altium.

Taidot: PCB Design and Layout, Analog Electronics, Electronic Design, Circuit Board Layout, Piirisuunnittelu

Näytä lisää: select design research project, pcb project simple circuits designs, schematic design pcb layout rf device, pcb design pdf project, schematic design pcb, pcb schematic design gsm gps, pcb layout schematic design, will design pcb schematic, pcb layout design project based, schematic design pcb layout, pcb design freelance project, please bid on this project exactly 36usd https www freelancer com projects graphic design design several banners for advertising, The main objective of this project is to design a multivariable state feedback roll bite controller to maintain a desired thickn, Hi there, I need some business card design urgently. If you think you are best candidate for this project please tell me somethi, PCB and schematic design for Ultrasonic Device, pcb schematic design software, pcb schematic design tutorial, design a cybersecurity strategy for defending against the attacks in this project, pcb schematic design

Tietoa työnantajasta:
( 8 arvostelua ) Lima, Peru

Projektin tunnus: #32239775

Myönnetty käyttäjälle:

(9 Arvostelua)
4.6

28 freelanceria on tarjonnut keskimäärin $294 tähän työhön

avigupta0061

Best Altium Design Expert at your doorstep! Dear Client, We can design schematic and PCB based on Altium/Eagle using a microcontroller for get 100ma minimun current in the 0-10 voltage output in design. We have exten Lisää

$1800 USD 20 päivässä
(31 arvostelua)
6.8
(36 arvostelua)
5.9
(29 arvostelua)
6.1
(26 arvostelua)
5.5
HarimohanG

Hi I can design schematic and PCB based on Altium/Eagle using a microcontroller in a quality and timely manner. I have seen the attached document you shared. I have humungous experience in Altium/Eagle based PCB desig Lisää

$180 USD 2 päivässä
(3 arvostelua)
5.1
(35 arvostelua)
5.2
Devpro11

Hello there. I hope to work with you because your project is very familiar to my past works. [login to view URL] I have 9+ years of experience in Electrica Lisää

$200 USD 5 päivässä
(11 arvostelua)
4.8
(11 arvostelua)
4.7
(8 arvostelua)
4.9
etalhak

Hello, I am an electronics and telecommunication engineer and my major is wireless systems' design. I am experienced in hardware and embedded systems' design. I have designed/printed/tested many PCBs and I am quite exp Lisää

$200 USD 7 päivässä
(24 arvostelua)
4.7
pcbdesign88vn

Dear you, I have 10 years to design circuit in Altium.I have read all yiir requirement and i can give you the best. Brg!

$100 USD 7 päivässä
(14 arvostelua)
4.6
RachelBenita

Hello, thank you for your job posting. I have 5 years experience in PCB and circuit design and Manufacturing, Embedded programming, and i can help you with any kind of request in these fields. I will do my best to sati Lisää

$250 USD 5 päivässä
(4 arvostelua)
4.2
engrhassanwali

Hi! I have understood your requirnments about your project with every detail of it. I am an Electrical Engineer with more then 9 years experience in electronics, circuit design, PCB layout, Verilog, FPGA, Embadded Syst Lisää

$250 USD 7 päivässä
(4 arvostelua)
3.3
AliIjaz1

Hello. I am an electrical engineer and experienced in PCB designing. I can help with your project. Please leave me a message to discuss further. Thanks

$200 USD 7 päivässä
(4 arvostelua)
3.1
pilpanikoba

Hello How are you? Thanks for your posting job. I have read your project requirements and I am 100% sure I can complete your project perfectly. ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ I have 15 years experience in Circuit & PC Lisää

$150 USD 7 päivässä
(5 arvostelua)
3.7
lydialin2000

1 ) I have over 20 years of experience in PCB Layout, HW, RF, EMI, FW, PSpice … etc. We can complete various design and layout requirements and Android / iOS app development. # 8051 MCU / ARM Embedded system / Ardui Lisää

$450 USD 7 päivässä
(2 arvostelua)
3.3
(2 arvostelua)
3.2
Shahabijan

I have been teaching in universities since 2014. Have done my masters in robotics. I am an assistant professor at a university in Pakistan in EE Dept. I have been teaching since 2014 and am also working on my PhD in co Lisää

$200 USD 7 päivässä
(1 arvostelu)
0.6
kimmontero5

CERTIFIED PHD HOLDER IN SOFTWARE ENGINEERING AND DEVELOPMENT. DEGREE IN COMPUTER SCIENCE EXPERT IN CYBER SECURITY, PYTHON, JAVA, C#, C++, JAVASCRIPT, AND DATA MINING. HELLO DEAR CLIENT. I have thoroughly gone through y Lisää

$150 USD 3 päivässä
(0 arvostelua)
0.0
rafatdawod

I have been working as a electrical power engineer for over 13 years. My expertise cover, Electrical circuit design Shop drawing Eplan Autocad PLC Mikro C (pic microcontroller) Arduino PCB design Soft-Starter Motors Lisää

$100 USD 7 päivässä
(0 arvostelua)
0.0