Suljettu

PI CM3+ Compute Module Schematic and PC Design

Create Circuit Boards for Raspberry PI Compute Module 3

Breakout Board for Raspberry Pi CM3+

2X USB A Ports

1X DSI Input for Display

4X buttons (to trigger GPIO )

1X Ethernet Port

2X CAN BUS (1 MBIT with MCP2515 based on PICAN DUO Layout) 120 ohm End resistors should be broken out to the main connector to be able to enable / disable via loop on main connector

8X Analog 0-5 V inputs (with overvoltage protection )

8x Digital 5 - 14 V inputs (overvoltage protection optocupler ?)

1X LDR Sensor (To be able to automatically dimm the display)

1X Real Time Clock incl button battery

1x Speaker

1x Voltage Converter with Shutdown Circuit (10-15 V input ) Stepdown to 5,1V and 3,3 V .(Voltage loss should trigger a GPIO pin so I can switch off the Pi safely by monitoring the PIN )

 Switched 12 V input should trigger the Circuit to switch on the CM . There should be a Capacitor which can supply enough power to the PI CM for 20 Seconds in order to trigger a safe shutdown via GPIO Pin , as well as stabilize the Power during cranking of the CAR .

1x WIFI with external Antenna Connection

There should be 1 34 Way Connector (Amp Superseal 2-6447232-3) for the following connections

1x Sensor Ground 9 Ground for the Analog inputs

8x Analog inputs

2x CAN High

2x CAN Low

8 x Digital inputs

1x 10-14 V Input

1x Main Ground

1x 3,3 V out

1x Ground out

1X SDA out

1X SDL out

2x Bridgeable pins for CAN 1 120 Ohm resistor

2x Bridgeable pins for CAN 2 120 Ohm resistor

Separate PCB’s ( To plug and play for modularity )

1x GPS Ublox Neo M8N via Serial with external Antenna Connection

6x Adressable RGB led on separate PCB mounted in one row

Taidot: PCB Design and Layout, Piirisuunnittelu, Raspberry Pi

Näytä lisää: raspberry pi compute module documentation, compute module io board v3 manual, raspberry pi compute module 4, raspberry pi compute module, raspberry pi compute module display, compute module io board v3 schematic, raspberry pi compute module io board, raspberry pi compute module carrier board, raspberry pi compute module motherboard, raspberry pi compute module custom board, raspberry pi compute module tutorial, raspberry pi compute module projects, raspberry pi compute module 3 wifi, raspberry pi compute module 3 ethernet, raspberry pi compute module 3 projects, raspberry pi i/o board for compute module 3, raspberry pi ™ compute module development kit, raspberry pi compute module 3 pinout, what is the raspberry pi compute module used for, raspberry pi compute module wifi

Tietoa työnantajasta:
( 4 arvostelua ) Pretoria, South Africa

Projektin tunnus: #26946508

10 freelanceria on tarjonnut keskimäärin 210$ tähän työhön

sagradoamicus

Hi I am experienced electronics engineer with more than 15 years of experience in PCB design. I have read the details and have a few questions. Please get in touch to discuss it further Regards

$750 USD 7 päivässä
(44 arvostelua)
6.7
a232004

Hello_dear_project_owner;Thank_you_for_posting_that_project;You_can_read_about_me_below; About_your_project I_am_doing_schematic,PCB,SW\FW_design_every_day_(I_design_and_make_industrial_electronic_equipment_–_Ultrasoni Lisää

$30 USD 7 päivässä
(22 arvostelua)
4.7
VujicicM

Hi, I'm very glad to have an opportunity to help you with PCB design! This job is VERY appealing to me because I have a lot of experience in circuit and PCB design of various kinds of IoT devices using Arduino, Raspb Lisää

$140 USD 7 päivässä
(4 arvostelua)
4.5
avigupta0061

Best PCB Design Expert at your doorstep! Dear Client, I couldn’t stop myself from bidding after going through the description as they are an exact match with my skillset and experience. I have experience in PI CM3 Co Lisää

$180 USD 2 päivässä
(8 arvostelua)
4.6
SMBelectronics

Greetings!! I read the overview of your project and am interested in working with you. I am an ELECTRICAL/ELECTRONICS ENGINEER from India with 4+ years of experience in designing circuits and PCBs. With my precision an Lisää

$250 USD 3 päivässä
(13 arvostelua)
4.5
HarimohanG

Dear Client, I have read and understood your requirements and could do it for you in the least time and utmost superior quality. I have experience in PI CM3 Compute Module Schematic and PC Design and could design it fo Lisää

$180 USD 2 päivässä
(1 arvostelu)
4.2
saddamgul842

Hi dear I am an electronics engineer and I have industrial experience of power electronics circuit and PCB layout designing. I did read your project description and can design a PCB layout up to 16 layers. Share your p Lisää

$130 USD 7 päivässä
(9 arvostelua)
3.3
hsh564cf84accd96

Hi my Professional Aim is: (Services then Solutions then Satisfactions) I hope you are [login to view URL] an experience in this field from last 5 years i am sure i can do it perfectly with in a time and budget Able to deliver y Lisää

$140 USD 7 päivässä
(1 arvostelu)
1.4
dewsoft3

Hi, "I have gone through your description. "This is my area of specialization, i can get it done perfectly well. Please ping me in person. I can help you to complete all tasks. I and my team have hands-on experience i Lisää

$225 USD 7 päivässä
(0 arvostelua)
0.0
STManikandan

Hello friend, I am an electronic engineer and Developer.... Great expertise in Circuit and pcb designing..... I can do the development....

$70 USD 7 päivässä
(0 arvostelua)
0.0