
Closed
Posted
Paid on delivery
I’m kicking off the complete design of a brand-new X-ray system dedicated to security screening of bags and hand luggage. This project starts at concept level and goes all the way through to a manufacturable design, so I’m looking for a specialist (or team) who can blend radiation physics, mechanical engineering, electronics, and image-chain know-how into one coherent solution. Scope • Source & detector selection: energy range and dose rates suitable for typical airport-style carry-on screening, while keeping radiation leakage well below IEC/ANSI limits. • Mechanical architecture: tunnel size around 550 mm × 400 mm, conveyor, lead shielding, safety interlocks, emergency stops, and ergonomic operator console. • Electronics & control: high-voltage generator design/selection, detector readout boards, motion control for the conveyor, and firmware interfaces (prefer STM32 or similar). • Image chain: basic real-time image acquisition pipeline; full software is not required now, but the hardware must expose standard GigE Vision or USB3 headers for later integration. • Compliance pack: 3-D CAD (SolidWorks or equivalent), full BOM, thermal and radiation shielding calculations, and draft regulatory file aligning with IEC 61010-2-091 and FDA 21 CFR 1020.40. Deliverables 1. Concept drawings and block diagrams for sign-off. 2. Detailed 3-D CAD and engineering drawings (STEP + native files). 3. Schematics, PCB layouts, and Gerbers for all custom boards. 4. Simulation reports (ANSYS/COMSOL for structure & shielding, MCNP or Geant4 for dose mapping). 5. Preliminary safety and compliance dossier. Acceptance criteria • Dose measurements in simulation stay under 0.5 µSv/h at 5 cm from any surface. • Image chain achieves minimum 0.5 mm wire detectability at 160 kV, 1 mA in single-scan tests. • All documents are complete, editable, and delivered in the agreed native formats. If you have a proven track record designing security or industrial X-ray equipment and can move quickly from concept to production-ready documentation, let’s talk details.
Project ID: 40797974
59 proposals
Remote project
Active 4 days ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
59 freelancers are bidding on average $514 AUD for this job

My strongest fit is the electronics and embedded architecture of your security X-ray system: I am an Electrical Engineer with a Master’s in Embedded Systems and experience taking connected products from system architecture and schematics through PCB design, firmware, and production-ready enclosures. STM32 and other industrial microcontrollers, embedded C/C++, RTOS, DMA, FPGA signal processing, high-speed PCB layout, and precision motor control align directly with your detector readout, conveyor control, firmware interfaces, and future image-acquisition requirements. My experience with image processing, industrial automation, and 3D CAD also supports the integration of the operator hardware, electronics, and mechanical housing into one coherent design. I can contribute the electrical, embedded, PCB, image-chain, and CAD expertise needed to develop a complete engineering package, while keeping radiation physics, shielding calculations, and IEC/FDA compliance documentation within the appropriate specialist review scope. I would welcome the opportunity to support this project from concept architecture through manufacturable documentation.
$3,500 AUD in 30 days
8.5
8.5

Greetings, I worked on a vehicle measurement system involving ESP32, calibrated sensor acquisition, and real-time data processing, along with several STM32-based hardware and firmware projects. My experience covers PCB design, sensor interfaces, embedded control, and hardware integration. For your X-ray system, the main challenge will be coordinating detector acquisition, conveyor control, safety interlocks, and radiation shielding into a reliable design. I can handle the electronics and control architecture, while radiation calculations, high-voltage design, and compliance validation should involve qualified X-ray specialists. I suggest starting with a concept design and technical architecture within 5–7 days for AUD 650, then estimating the full engineering work as separate milestones. Do you already have a preferred X-ray source and detector, or should these be selected from scratch? Sincerely, Oleksandr Gergel
$650 AUD in 7 days
8.4
8.4

Hi, I am an embedded systems engineer with over 16 years of experience. I have extensive experience with custom electronics, embedded controls and product development from concept through production, and can also support the STM32 firmware. For your baggage scanner, I would first align the source and detector selection with the tunnel layout, conveyor controls and safety architecture, then define the image acquisition interface for later software integration. Radiation leakage and wire detectability would be validation requirements, supported by specialist analysis and eventual physical testing. The complete CAD, electronics, simulation and compliance package is a substantial multidisciplinary undertaking. My AUD 1,200 bid covers an initial 14-day concept and feasibility milestone: concept drawings, block diagrams, a preliminary component shortlist and a development plan. Detailed engineering and production documentation would require separately agreed milestones and timelines. The bid exceeds your listed range to reflect the initial engineering scope, and I am flexible on milestone structure. Is your current budget intended for the concept phase, and do you have preferred source or detector suppliers? Please contact me to discuss details.
$1,200 AUD in 14 days
7.7
7.7

Yes, I can provide the mechanical design in STEP format along with the native editable CAD files (SolidWorks or Fusion 360, depending on the agreed workflow). For the complete project, I can also provide editable schematics, PCB source files, Gerbers, BOM, engineering drawings, and technical documentation. All deliverables will be organized and prepared for future manufacturing and engineering revisions.
$500 AUD in 7 days
7.3
7.3

My 9 years of experience as a professional mechanical designer make me well suited to develop the 3D mechanical architecture for your security X-ray system, from the tunnel and conveyor arrangement through to manufacturable CAD documentation. I specialize in 3D CAD and can produce clear concept layouts, detailed models, assemblies, and engineering drawings for the enclosure, conveyor structure, operator-facing components, shielding integration, and safety-related mechanical provisions. My image-processing skills also align with the required image-chain considerations and future integration of the imaging hardware. I will keep the design organized for editable native files and STEP delivery, while supporting the wider BOM and documentation package with a practical manufacturing focus. I would be glad to contribute reliable mechanical design expertise to this project and help turn the X-ray system concept into production-ready documentation.
$250 AUD in 2 days
6.6
6.6

Hi there, I can assist with the mechanical design and 3D modelling of a security X-ray inspection device, focusing on structural integrity, component integration, thermal management, and manufacturability. I have 7+ years of mechanical engineering and CAE experience, covering mechanical design, CAD modelling, FEA, and engineering validation. Deliverables: - Complete 3D CAD assembly and component modelling. - Enclosure, conveyor, and mechanical support design. - Component arrangement and assembly integration. - Structural and thermal FEA, where required. - Material selection and design optimisation. - Detailed manufacturing drawings and BOM. I can work with SolidWorks, ANSYS, and other mechanical engineering tools. Could you share the device specifications, reference images, and expected design scope? Timeline and budget can be finalized after discussing the complete scope. Best regards, Arati M.
$500 AUD in 7 days
6.6
6.6

My experience with 3D CAD and engineering design makes me well suited to develop the mechanical architecture of your security X-ray system from concept through detailed, manufacturable documentation. I can create the tunnel enclosure, conveyor arrangement, operator-console concepts, safety-interlock locations, and production-ready 3D models using tools including SolidWorks, CATIA, AutoCAD, Revit, and related CAD platforms. My electrical engineering skill set also supports the system-level coordination required between the mechanical structure, generator, detector, control electronics, and future image-chain interfaces. I can deliver clear concept drawings, engineering drawings, editable CAD/native files, and coordinated documentation while keeping the design organized for fabrication and further compliance review. I would be pleased to contribute to this project with precise CAD development and integrated engineering support, and I invite you to choose me to help turn the X-ray screening concept into a coherent design package.
$258 AUD in 3 days
6.4
6.4

⭐⭐⭐⭐⭐ Your project requires a carefully coordinated engineering approach, combining radiation safety, mechanical architecture, electronics, and image acquisition into one manufacturable X-ray screening system. I'd recommend beginning with a system feasibility and architecture phase before committing to detailed CAD, custom electronics, and simulation. My proposed development approach includes: Defining the X-ray source, detector architecture, and image-chain requirements. Developing the 550 × 400 mm tunnel, conveyor, shielding enclosure, and safety-interlock architecture. Designing the electrical, control, and embedded-system interfaces. Developing the mechanical CAD, PCB documentation, BOM, and manufacturing drawings. Preparing structural, thermal, and radiation simulation documentation. Compiling the preliminary safety and regulatory compliance dossier. I'd structure the work around documented engineering reviews and measurable acceptance criteria, with independent radiation-safety verification before any operational deployment. Could you confirm whether you already have access to a certified X-ray generator and detector, or should their selection and procurement be included in the engineering scope? I'd welcome the opportunity to discuss the initial feasibility stage and establish a realistic development plan.
$500 AUD in 7 days
5.8
5.8

I'm a Senior Electronics Engineer with over 7 years of experience in PCB design, embedded firmware, power electronics, high-speed interfaces, and complete hardware product development. I work with a multidisciplinary team covering electronics, embedded systems, mechanical engineering, and 3D CAD design. We can support complex projects from system architecture through prototype development and manufacturing documentation. My relevant experience includes a complex x86 hardware platform featuring PCIe, USB 3.0, Ethernet, multiple power supplies, and high-speed PCB design, along with STM32-based industrial data acquisition and control systems. For your X-ray security screening system, I can contribute to: System architecture and electronic block diagrams. High-voltage generator interface and control electronics. Detector readout, signal conditioning, and data acquisition. STM32-based conveyor control, safety interlocks, and firmware. USB 3.0/Gigabit Ethernet hardware integration. Schematics, PCB layouts, Gerbers, BOM, and manufacturing documentation. Mechanical integration and 3D CAD coordination. Radiation shielding, source selection, and regulatory verification would require a qualified X-ray systems specialist or medical physicist working alongside our engineering team. I'd welcome the opportunity to review your requirements and discuss a practical development plan, milestones, and responsibilities. Best regards, Yaroslav
$500 AUD in 7 days
5.9
5.9

This is not simply a mechanical modeling or PCB design task; it requires mechanical engineering, robotics, electronics, embedded control, imaging hardware, and radiation engineering. My experience combines machine design and manufacturing with robotics, automation, and electronics. I have worked on machinery, robotic mechanisms, electromechanical systems, custom circuits, PCB layouts, embedded controllers, and automated motion systems. My focus is practical engineering, integration, and manufacturability. I understand your requirements, including the conveyor, screening tunnel, X-ray source and detector, radiation shielding, high-voltage systems, STM32 control, detector interfaces, thermal analysis, and engineering documentation. A project of this complexity cannot be treated as a basic design task worth a few thousand dollars. Based on my experience in machinery, robotics, and automation, a complete engineering design should start at approximately $40,000, excluding manufacturing, component procurement, and certification. Hiring a freelancer engineer is a major project investment. You are paying for engineering expertise, practical experience, technical judgment, and the ability to transform a complex concept into a manufacturable product, not simply for drawings and simulation files.
$500 AUD in 7 days
5.3
5.3

Hello there, I can support the X-ray system development, including mechanical CAD, electronics integration, embedded control, BOM, and engineering documentation. I can deliver editable STEP, SolidWorks, and PDF files with iterative design reviews. Ready to start with concept development and system architecture. Best regards, Aryans
$500 AUD in 7 days
5.8
5.8

My strongest fit for this project is the combination of 3D CAD, SolidWorks-oriented mechanical design, electronics, and PCB design/layout. I can support the transition from concept drawings and system architecture to detailed mechanical models, engineering drawings, custom-board documentation, and editable manufacturing files for your security X-ray enclosure. My experience with AutoCAD, CATIA, Abaqus, Rhino, Revit, SketchUp, and related 3D tools supports the tunnel, conveyor, console, shielding-enclosure, and structural design requirements. My Electronics and PCB Design and Layout skills also align with the control electronics, detector interfaces, readout boards, and future GigE Vision or USB3 integration. I can prepare organized CAD, schematics, layouts, Gerbers, BOM documentation, and supporting design calculations while keeping the deliverables in native and standard formats. I would be glad to contribute to this complex product from concept through manufacturable documentation and provide a professional, coordinated design package for your review.
$251 AUD in 1 day
5.7
5.7

My physics background in atomic and nuclear physics, electromagnetism, materials science, and computational physics is directly relevant to the radiation, shielding, dose-mapping, and image-chain documentation required for this security X-ray system. I can support the project with technically rigorous calculations, modeling, analysis, and clear engineering documentation from concept through preliminary compliance review. My skills also include mechanical engineering, electrical engineering, 3D CAD, MATLAB, numerical methods, and scientific data visualization. This combination can contribute to the tunnel and shielding architecture, thermal and radiation calculations, system block diagrams, technical reports, BOM documentation, and editable compliance material aligned with the stated IEC and FDA requirements. My research and technical-writing experience is especially valuable for producing organized simulation reports and a coherent safety dossier. I would be glad to contribute my physics, engineering, modeling, and documentation expertise to this project and help develop a well-supported foundation for production-ready X-ray equipment design.
$750 AUD in 60 days
5.0
5.0

Hi, I’m interested in working on your X-ray security screening system. I have a background in software engineering, electronics, and AI development, and I can contribute to the embedded control, image acquisition, system integration, and technical documentation. I understand this project requires careful coordination between mechanical, electrical, and radiation engineering. I’m comfortable discussing the requirements and working with the right specialists to develop a reliable solution. I’d be happy to discuss the project scope, timeline, and next steps. Best regards
$750 AUD in 3 days
4.8
4.8

This is not an AI-generated bid like all the others I saw. As you can see in my portfolio on my profile, I have extensive experience designing PCBs and mass production equipment, just like you need. I can handle your project. I apologize for the simple proposal; I know you're probably tired of reading AI-generated proposals, and I'd rather not waste time on that. If you're interested in working with me, send me a message and we can work out the details! Best Regards!
$500 AUD in 7 days
4.8
4.8

I understand you need a comprehensive design for a new security X-ray system, similar to how I've integrated complex physics simulations with manufacturable CAD for advanced imaging devices in previous projects. My experience in optimizing radiation sources and detector arrays for specific energy profiles and dose rate constraints directly aligns with your need for airport-style carry-on screening while maintaining stringent safety limits. My approach will involve a phased development. Initially, I'll perform detailed Monte Carlo simulations (e.g., Geant4) to model radiation transport and optimize source/detector selection for the target materials and throughput. Concurrently, I'll develop preliminary mechanical concepts using CAD software (e.g., SolidWorks) to ensure efficient shielding and robust construction, followed by detailed electronic schematic design and component selection for the image chain, focusing on low-noise amplification and high-speed data acquisition. To ensure we're perfectly aligned, could you specify the desired throughput for the system and any existing regulatory frameworks beyond IEC/ANSI that are critical for your target market? I’m eager to discuss how my expertise can translate into a robust and compliant security X-ray solution for your project.
$738 AUD in 21 days
4.3
4.3

✅✅✅✅✅ This is an exciting multidisciplinary engineering project, and I would be interested in helping develop the system from concept through detailed engineering and manufacturing documentation. My strongest contribution would be in electronics development, PCB design, embedded control, and hardware integration. I can work on the STM32-based control architecture, detector interface electronics, high-voltage generator control interfaces, conveyor electronics, safety monitoring, and hardware interfaces for future GigE Vision or USB3 image acquisition. I would approach this in structured stages: Define system architecture and select suitable hardware components. Develop mechanical CAD, electrical schematics, and custom PCB layouts. Implement embedded control and hardware communication interfaces. Coordinate thermal, structural, and radiation simulation activities with appropriately qualified specialists. Prepare manufacturing files, BOM, engineering drawings, and technical documentation. I understand that radiation shielding, leakage limits, and regulatory compliance are critical. These must be supported by validated calculations and independent testing rather than assumptions. A few questions: Do you already have preferred X-ray source and detector manufacturers, and do you have an existing reference design or are we starting entirely from scratch? I'd be glad to discuss the technical scope and establish a realistic development plan.
$500 AUD in 7 days
4.4
4.4

Dear Client, I can support development of the security X-ray system from system architecture through electronics, control hardware, PCB design, detector interfaces, conveyor control, safety interlocks, and manufacturing documentation. PCB Must Innovations has 30+ years of experience in electronics/PCB development across STM32-class controllers, high-voltage interface electronics, sensor acquisition, motor control, safety interlocks, power systems, multilayer PCB design, EMI/EMC, and production support. I can develop the electrical architecture, detector/readout interfaces, conveyor and interlock control, emergency-stop logic, custom PCBs, GigE/USB3 hardware interfaces, BOM, Gerbers, and manufacturing documentation. For radiation shielding, dose mapping, and IEC/FDA compliance calculations, I would involve a qualified radiation/X-ray specialist rather than overstate capability. The same applies to MCNP/Geant4 validation if required. The important part is defining the X-ray source, detector geometry, shielding, image-resolution target, and safety architecture together before mechanical or PCB design is frozen. One question: have you already selected the 160 kV X-ray source and detector technology, or should source/detector trade-off analysis be part of Phase 1? Message me with that answer and I’ll outline the electronics, safety, imaging-interface, and prototype-development path before you commit. Kind Regards Prat PCB Must Innovations
$465 AUD in 7 days
6.4
6.4

Thank you for the project posting. I will approach this project by developing a coordinated X-ray screening system architecture, covering the mechanical tunnel, conveyor, shielding enclosure, operator console, and integration of the source, detector, and control electronics. I have 12+ years of experience in mechanical CAD and engineering design, with a focus on detailed 3D assemblies, manufacturing drawings, and engineering documentation. I will prioritize manufacturability, component integration, and design validation while ensuring that radiation physics, shielding calculations, and regulatory compliance are addressed through appropriate specialist review. Deliverables: Concept layouts and system block diagrams Detailed 3D CAD models in SolidWorks and STEP Mechanical manufacturing drawings and BOM Electronics schematics, PCB layouts, and Gerber files Structural, thermal, and radiation shielding analysis documentation Preliminary safety and regulatory compliance dossier Could you please clarify: Do you already have preferred X-ray source and detector manufacturers, or should these be selected from scratch? Is the project intended for a laboratory prototype or commercial airport deployment? Will you provide access to radiation physics and regulatory compliance specialists for the required validation? Kind Regards..
$260 AUD in 4 days
4.2
4.2

I am a Mechanical/Mechatronics Engineering researcher with extensive experience in multiphysics simulation, mechanical design, and engineering analysis using ANSYS and COMSOL. I can contribute to the mechanical architecture and structural design of the X-ray baggage screening system, including conveyor mechanisms, tunnel structure, component integration, thermal analysis, and radiation shielding simulations. My expertise includes 3D CAD development, FEA, CFD, material selection, and performance optimization. I can also support radiation shielding assessment and dose-distribution studies through suitable numerical modeling approaches, in coordination with qualified radiation and electronics specialists. I will focus on developing a technically sound, optimized, and manufacturable design supported by simulation results, engineering drawings, and comprehensive technical documentation. I would welcome a discussion to define the project requirements, technical responsibilities, and deliverables.
$500 AUD in 7 days
4.2
4.2

Abu Dhabi, United Arab Emirates
Payment method verified
Member since Nov 11, 2020
$25-50 USD / hour
$30-250 AUD
$250-750 AUD
$30-250 AUD
$10-30 AUD
₹600-1500 INR
£1500-3000 GBP
$250-750 USD
₹600-1500 INR
₹12500-37500 INR
$10-30 USD
$10-30 USD
₹1500-12500 INR
$250-750 USD
₹600-1500 INR
$1500-3000 USD
₹600-1500 INR
₹1500-12500 INR
min $50 USD / hour
$10-30 USD
$75-125 USD
$30-250 USD
$750-1500 AUD
$10-30 USD
$10-30 USD