Peruttu

pin board 2013

i am looking for a device to be made i have tried to do a few ways so far i tried with solenoid and coils. I have not been able to get it done due to cost.

i need to have have a board of 400 pins that look a bit like a pin art toy.

(they are arranged like a a grid 20 by 20) moved automatically

I wish to be able to move some or all of the pins up or down at the same time and then the pins to stay in place

I have tried to replace the pins with linear actuators but the cost sky rockets as each actuator costs 15 - 50 dollar x 400 =6k 30k

So i need a cheap way to move the pins the cheapest way i can think of is to have a mechanical flick switch on the pin moving it up 1 mm at a time and another moving it down 1 mm at a time. by a device under the board .

another way is to use mobile phone vibrator actuators

another is use a crayola twistable with the crayon replaced by a plastic bar and a plastic motor at the bottom with 10 spins should fully extend the bar.

another is to have 3 tubes one inside other with middle one has magnet and insulation. Inner and outer have copper coils opposing each other seperated by insulation elec applied to inner coil pushes up middle tube and elec applied to outer tube puses down plastic tube by varing the power between both you can vary height of tube.

I am sure there are other ways i am very open to otherways

the target price of this board will be about 2k

The pins will rise 100mm above the board and the board will be 200mm by 200mm

ideally i would like less space between the pins. the pins should be square and between 9mm and 6mm wide.

There is minimal load on the pins

the board will need to be computer controlled with a simple interface where each pin can be numbered and each pin can be instructed to go to the required height.

Every few seconds the board will be given a new set of heights for the pins to go to this should only take a few seconds.

I am open to ways the pins can be moved but i will need a workable approach before i award the project.

i will need six of these boards to be made so all can be controlled by the same computer at the same time.

Taidot: tekniikka, Valmistuksen suunnittelu, Koneenrakennus, Mekatroniikka, Solidworks

Näytä lisää: solidworks art, price of solidworks, pin art cheap, mechanical engineering costs, mechanical engineering cost, costs for mechanical engineering, computer engineering price, cheap mechanical engineering, cheapest solidworks, cheap art, toy art, simple toy, rockets and, power elec, pin, pin down, mechanical new, load board, i looking for new project in art, elec, crayon, motor load, solidworks tube, mobile grid, solidworks engineering

Tietoa työnantajasta:
( 62 arvostelua ) Dublin, Ireland

Projektin tunnus: #4399645

8 freelanceria on tarjonnut keskimäärin 4442 $ tähän työhön

anujgargiitk

Hi, I am a mechanical engineers with extensive experience in design of complex mechanical systems and have completely understood your technical requirements. As such I have designed different kinds of aircrafts and oth Lisää

5000 $ USD 50 päivässä
(10 arvostelua)
5.0
caddesignguru

Hi,we can help you to complete this project,please see PMB for more detail, Thanks.

3150 $ USD 30 päivässä
(3 arvostelua)
4.6
udayd75

We provide services, please check private message

5000 $ USD 20 päivässä
(2 arvostelua)
2.8
surajvmohan

Hello Sir, I am a Mechanical Engineer from the Indian Institute of Technology Madras(IIT). I am also a part of the FSAE team of my college. I have designed the whole 2013 car. Hence, I can assure that I am very good at Lisää

4000 $ USD 15 päivässä
(7 arvostelua)
2.8
amienaeem

i have to the solution , . . . . .read my PM

5000 $ USD 20 päivässä
(2 arvostelua)
2.1
rotek

Sounds like interesting project. Let's do it!

4545 $ USD 45 päivässä
(0 arvostelua)
0.0
racul07

Hello, I have 9 years experience ! Expect more details! Thank you !

4444 $ USD 44 päivässä
(0 arvostelua)
0.0
iceg001

can you draw a sketch of how this will look like with approximate motions you want it to do? that way it would be easier to design a working prototype

4400 $ USD 30 päivässä
(0 arvostelua)
0.0