Re-Design/Tweak already made PCB to be CE/UL/FCC/APPLE Compliant and Ready for Manufacturing

$30-75 USD

Peruutettu

Julkaistu

yli 10 vuotta sitten

$30-75 USD

Maksettu toimituksen yhteydessä

I have a PCB that was built and designed already but word came back from the manufacturer that it will not pass the required certifications. It is a Phone/Tablet Multi Charger (AC to DC converter with Pass Through outlets). Looking for an Electrical Engineer that specializes CE Compliance, FCC Compliance, UL Compliance and in Compliance with any APPLE regulations since it is a charger for their device in order to get the PCB ready for Manufacturing and Certification. I will send all schematics, BOM, GERBER files and anything else I have related to the project. Any changes needed in order to correct the layout to allow compliance with the Authorities will require updating all essential files and returning to me so that I can order the boards at the end of the project. Thanks for looking. Attached is a picture of the board.

Electrical Engineering

Projektin tunnus (ID): 5018450

Tietoa projektista

2 ehdotukset

Etäprojekti

Aktiivinen 11 vuotta sitten

Haluatko ansaita rahaa?

Sähköpostiosoite

Freelancerin tarjouskilpailun edut

Aseta budjettisi ja aikataulu

Saa maksu työstäsi

Kuvaile ehdotustasi

Rekisteröinti ja töihin tarjoaminen on ilmaista

2 freelancerit tarjoavat keskimäärin $128 USD tätä projektia

@betaenergy

Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of hardware For each concept descriptions are as follows: Digital Motor Control: -3-phase induction motor vector control drive -Flux estimation algoritm generation -DSP(TMS320) implementation on motor drive -Low speed application -Torque and speed loop generation -Control algoritms Analog design -Low power distribution -Noissless special opamp based analog circuits -Analog filters -Orcad simulation of several circuits Electronic Design -RF transmitter and receiver -Bluetooh reader and transmitter -Magnetic reader Power Electronics -Implementation motor drive -AC/DC converter -DC-DC converter -Battery charger -Solar inverter -Renewable Energy simulations -Uninterruptle power supplies PCB design -Schematic design by Altium -PCB design by Altium -Power board design -SMPS board design Embedded system -PIC18,PIC24,PIC30 and dsPIC applications -Ardino -MSP430 -Atmel -DSP(Texas Instruments) -Renesas Matlab -Power Electronics simulation -Motor drive -Wind Energy -Solar Energy -Control applications Simulation of Hardware -Orcad Simulation(TI,National, Linear Tech, Maxim libraries) -LTI -National -Matlab Very important Note: References attached. Please look excel file to see projects which we made until now! Metin

$157 USD 3 päivässä

4,8

(12 arvostelua)

4,9

@GlobalElectronic

Dear I have master degree from electronic and i work as professional circuit and PCB designer. I am offering you professional help fo you'r project. I have a lot of experiance related about standards in electronic, it is my everyday job, because my boss require from me same thing on each design. Please tell me in which PCB software the board is designed. I can update you'r layot up to morning, so you will have work done for around 15 hours from this moment. Please message me so we can go in details about project. Kind Regards Nemanja

$105 USD 1 päivässä

4,9

(11 arvostelua)

4,4

@akramkarimi1036

Greetings, I have extensive experience with Power Electronics (DC/DC Converters, AC/DC Rectifiers, DC/AC inverters etc) I can help you out... Electrical Engineer (Gold-Medalist) from the oldest and the most reputable engineering institute of Pakistan (UET, Lahore). Done my internship @ US based R&D embedded company “Mentor Graphics” and currently working as Professional “Embedded Design Engineer” @ Asia’s #1 ranked R&D company “MicroTech Industries”… Looking forward to your reply soon

$150 USD 20 päivässä