PCB Design Engineer — Finish & Validate a 4-Layer Sensor Board (KiCad, JLCPCB)

@mairajali11

As a seasoned Electrical/Electronics Engineer and PCB Designer with a passion for designing high-quality boards, I am confident in my ability to meet and exceed your expectations for this project. With over 8 years of experience using Eagle, Altium, KiCAD, and EasyEDA, I have extensive knowledge in taking boards through DRC to fabrication. This experience is complemented by my familiarity with KiCAD footprints from mechanical drawings, enabling me to seamlessly address your first open item by authoring a new IP67-rated USB-C connector footprint. In addition to my circuit design and PCB layout skills, I also possess solid expertise in battery charging circuits and adjacent layout considerations. I understand the importance of maintaining proper keep-out zones near sensitive components like an antenna, deeply aligning with the needs of your second open item. Choosing me means working with a dedicated professional who thrives on turning ideas into reality. With an estimated turnaround time that respects both the comprehensiveness and speed required of this project, I can assure you that the revised KiCad project I deliver would not only correct the shortcomings in your design but also ensure better functionality and reliability. Let's work together to bring your sensor board closer to completion with precision and efficiency. Feel free to reach out 24/7, let's get started!

@tshibsamuel477

Hi there, I have carefully reviewed your 4-layer ESP32-S3 sensor-board requirements and can independently validate the existing KiCad design, resolve the two remaining layout issues, and prepare it for JLCPCB fabrication. With nearly five years of experience in PCB design, KiCad/Altium, battery-powered electronics, USB-C, ESP32, RF-aware layout, custom footprint creation, power integrity, and DFM, I can handle the IP67 USB-C footprint replacement, charger/fuel-gauge placement and rerouting, antenna keep-outs, thermal-pad clearances, and full DRC review. I will provide the updated KiCad project, corrected BOM/CPL, final DRC report, and a concise review of all changes and remaining risks. Estimated turnaround is **3–5 working days** once I receive the project files and relevant datasheets. Please send me a message with the KiCad project and I can start the review immediately. Best regards, Samuel tshibangu

@vijay1307

Profile : ---------- over 20 years of experience in PCB layout design. Designed PCB using Blind/Burried Vias - Back Drilling - Rigid Flex Stack - Castellated holes Good knowledge on DFM, DFT and DFA Concepts. Exposure to Product development stages. Knowledge in High speed designs ,signal integrity, EMI, EMC concepts. Sound knowledge on Component creation, Design Rule settings, Library management and Customer deliverables with documentation. Educational Background : ------------------------ Bachelor Degree in Electronics & Communication Engineering CAD tool supported : ----------------------- 1. Pads VX2.1 standard / Pads Dxdesigner VX2.1 standard / Pads Logic 2. ORCAD PCB Designer Professional17.2 3. Eagle 4. Kicad 5. Altium Designer 23 Services Offered : ------------------ 1. Symbol Creation 2. Scheamtic Capture 3. Footprint Creation. 4. Place, Route ,Gerbers and TQ closure. 5. PCB Layout Review. Minimum Required Inputs : ------------------------- A top - level functional block diagram Schematic Netlsit BOM Mechanicals Impedance Information Current Consumption on each voltage rail. Target fabrication house - capability report Industries Served: ------------------------- • Medical Devices • Consumer Electronics • Industrial Equipment • Automotives • Safety and Security Equipment • Telecom

@ahsanfreelancer7

Hi, Hope you are well. It sounds like a great job and aligns with where I'd like to take my career. I'm eager to learn more. I have experience over the past fifteen years as a PCB Design Engineer at Global Engineering services and RWR Private Ltd. You can visit my freelancer profile page; https://www.freelancer.com/u/ahsanfreelancer7 I’ve been consistently committed to Specific goals, skills or traits the new job entails. Could we schedule some time to discuss about opportunity in more detail? I’d welcome the opportunity to learn more about the role and share how my skills and experiences would benefit you. I’m available to talk at any time. I look forward to speaking with you. Best, AHSAN ULLAH

@Adeel2k14

Hi, I’m a Hardware Design Engineer with extensive experience developing 4-layer, battery-powered ESP32 designs routed for JLCPCB manufacturing. I regularly author custom KiCad footprints to manufacturer datasheets, optimize battery/fuel-gauge power management, and enforce RF antenna keep-out boundaries. I will handle your scope end-to-end: authoring the IP67 USB-C footprint (G-SMT-TR-67), resolving the charger/fuel-gauge footprint collision and thermal-pad clearance, performing a thorough power/ESD schematic review, and delivering final DRC, BOM, and CPL files within 5–7 days. Let's discuss your project files and get this ready for production.

@Amidst

Hey there! I’m Alok, A PCB, Circuit and Mechanical designer with a passion for turning ideas into rock-solid, high-performance circuit boards. even expert on Python, C, C++ With nearly a decade of experience, I’ve tackled everything from compact consumer gadgets to complex industrial systems—always with a focus on precision, efficiency, and reliability. # Schematic & Layout Design – Clean, optimized, and manufacturable. # Component Selection & Library Management – No surprises, just the right parts for the job. # Reverse Engineering – PCB cloning, replication, and improvements. # Gerber, BOM & CPL Generation – Ready for seamless production. # DFM & DFA Expertise – Because great design means smooth manufacturing. # Multi-Layer, Flex, & High-Density PCB Design – Whatever the project needs. If you need a PCB and Code that’s efficient, reliable, and built for real-world performance, let’s chat. I’d love to help bring your project to life!

@debosx

Hello! I'm a highly skilled PCB Designer with over 10 years of expertise in delivering reliable and efficient PCB designs. I specialize in creating precision designs tailored to client's needs, utilizing top-tier design tools such as Altium Designer, Autodesk Eagle, KiCad, EasyEDA, Siemens PADS, DipTrace, Allegro/OrCAD, Fritzing and Proteus. My goal is always to ensure the highest quality and performance in every project. Core Expertise : • Schematic Capture & Layout Design • Component Selection & Library Management • Reverse Engineering (PCB Replication, PCB Cloning) • Gerber, BOM, and CPL File Generation & Manufacturing Support • Design for Manufacturability (DFM) and Design for Assembly (DFA) • PCB Design & Development (Single, Double, Multi-Layer, Flexible PCBs) Industries Served : • Medical Devices • Telecommunications • Consumer Electronics • Industrial Equipment • Automotive Electronics • Safety and Security Devices Why Choose Me? • Attention to Detail and Commitment to Quality • Strong Communication Skills & Client-Centric Focus • Timely Delivery & Flexible Approach to Meet Project Requirements I would love to help you with your next PCB design project. Feel free to reach out, and let’s discuss how I can bring your ideas to life! Best Regards, Utpal

@Mahmoud00Ibrahim

Hello, I can take your existing KiCad 10.x design through the final engineering review and prepare it for JLCPCB fabrication. I have extensive experience with 4/6-layer PCBs, ESP32/STM32 systems, battery-powered designs, USB-C, switching regulators, and manufacturing-focused PCB validation. I also design DC-DC converters for my automotive projects, so power integrity, thermal management, protection, and high-current routing are areas I work with regularly. I can handle the complete scope, including: Independent schematic and PCB review Re-running JLCPCB DRC and reviewing the ~195 tight-clearance findings Creating the new IP67 USB-C footprint directly from the manufacturer datasheet Replacing and routing the connector while maintaining ESP32 antenna keep-out Correct placement/routing of the charger and fuel-gauge ICs Resolving the exposed thermal-pad/power-trace short risk Reviewing battery charging, buck-boost/boost rails, USB-C, ESD/TVS, and I2C routing Final DRC, BOM/CPL updates, and manufacturing-ready KiCad files I focus on catching real manufacturing and reliability issues rather than simply making the DRC green. I can start immediately and complete the review and required changes within your 1–2 week timeframe. Best regards, Mahmoud

@shadabkhan92

Drawing on years of experience in circuit design, electrical engineering, electronics, embedded systems and PCB layout, I am confident in my ability to complete and validate your 4-layer sensor board project to meet your high standards. Not only have I been involved in all stages of PCB development — from schematic design to fabrication reviews — but I also have advanced intimate familiarity with KiCad and have previously authored footprints directly from manufacturer mechanical drawings/datasheets. My involvement extends past just the circuitry to elements like battery charging and adjacent layout, crucial for designing against load-bearing risks. The two open tasks you mentioned – a USB-C connector swap and battery charger + fuel gauge placement – are both well within my capabilities. As a team deeply experienced in edge hardware, we have had ample experience upgrading components due to problematic datasheets as well as maneuvering tight spatial constraints. Regarding the latter point, I worked with a similar round device on a previous project and successfully resolved thermal pad clearance issues that bear resemblance to your current short risk discovery.

@chetanc20

Proposal (Very Short): Hi, I can review, validate, and finalize your 4-layer ESP32-S3 KiCad PCB for JLCPCB fabrication. I have 5+ years of PCB design experience, including battery-powered IoT boards, USB-C, ESP32, and DRC/fabrication validation. I'll resolve the USB-C footprint and charger/fuel gauge layout issues, provide updated KiCad files, BOM/CPL, and a clean DRC report within the estimated timeline.

@ahmedy607

Hi, I carefully reviewed the project details, and this is a great fit for my experience with KiCad, multi-layer PCB design, and pre-manufacturing validation. I can independently review the board, resolve the USB-C footprint/placement and charger + fuel gauge routing issues, while checking DRC, thermal pad clearance, power integrity, and antenna keep-out requirements. I’m comfortable creating accurate KiCad footprints directly from manufacturer datasheets and preparing designs for JLCPCB production. Please feel free to check my portfolio for examples of my previous PCB work. I’ll provide the updated KiCad files, BOM/CPL, final DRC report, and brief review notes. Estimated turnaround: 5–7 days. Best regards, Ahmed Yahia

@alluankit01

Hi, I can review, finish and validate your 112mm round 4-layer ESP32-S3 sensor board in KiCad 10.x before JLCPCB fabrication. My approach will be to first audit the schematic, power rails, USB-C wiring, TVS/ESD coverage, I2C devices, LED ring driver, battery charger/fuel gauge area and antenna keep-outs. Then I’ll resolve the two open layout items and re-run final DRC. I’m comfortable with: * KiCad PCB review and cleanup * 4-layer PCB layout * JLCPCB/LCSC BOM and CPL preparation * USB-C footprint creation from datasheet * IP67 connector placement * Battery charger/fuel gauge routing * Thermal pad clearance checks * ESP32 antenna keep-out review * DRC/DFM validation Deliverables: * Updated KiCad 10.x schematic and PCB * New USB-C footprint and edge placement * Charger/fuel gauge footprint/routing fix * Resolved short/clearance risks * Updated BOM/CPL for JLCPCB * Fresh DRC report * Short review note with changes and concerns Estimated turnaround: **5–7 days** after receiving the KiCad project and datasheets. I’ll focus on practical fab-readiness, clear documentation, and making sure the remaining risks are closed before you place the paid JLCPCB order. Best regards Ankit

@nehasingh17

Hi, We at HardFault can review and finish your 4-layer ESP32-S3 sensor board and prepare it for a reliable JLCPCB fab run. We’ll independently check the schematic, power rails, USB-C, ESD/TVS, I2C, LED driver, antenna keep-out, thermal-pad clearances, and the ~195 borderline DRC findings. We can also create the correct C3197945 USB-C footprint from its datasheet, handle edge placement and re-routing, and resolve the charger/fuel-gauge footprint and thermal clearance issues. Final delivery will include the updated KiCad project, JLCPCB BOM/CPL, fresh DRC report, and concise review notes. As a team at HardFault, we can handle PCB layout, electrical validation, and manufacturing checks together to keep the 1–2 week turnaround efficient. Can you share the latest KiCad project so we can review the open items and confirm the fastest path to fabrication?

@rfandelectronics

As seasoned RF and Electronics Engineers with an unshakeable commitment to quality, my team and I are perfectly suited to ensure the success of your 4-layer sensor board project. Our vast experience includes managing complex PCB designs using KiCad and JLCPCB fabrication, making us an ideal fit for the tasks at hand. We work diligently to ensure that all aspects of a design have been thoroughly reviewed, running accurate DRC checks that conform to JLCPCB's specs. Our track record of identification and resolution of design issues will be valuable in ensuring a successful fab run without compromising on safety or quality. Our familiarity with battery charging circuits and the inclusion of keep-out zones near antennas will prove advantageous as we tackle the open items on your checklist. Our skills extend beyond just reviewing and validating designs; we actively propose solutions to identified problems, such as creating a new IP67-rated USB-C footprint authoring from real datasheets. We will also devise the most appropriate solution for placing the battery charger and fuel gauge PCB safely, mitigating any risks through close attention to thermal pad clearance. With our background in high-frequency PCB design bolstered by practical implementation in various projects, we can guarantee improved RF performance, optimal power architecture, and reliable data transmission on your

@anjalio22

I’d be glad to take this opportunity to finish and validate your 4-layer sensor PCB in KiCad 10.x. I have experience with PCB layout, schematic review, DRC validation, JLCPCB manufacturing requirements, component footprints, and battery-powered embedded hardware. I will independently review the complete schematic and PCB, verify the power architecture, USB-C, ESD/TVS protection, I2C, LED driver, antenna keep-out, and the reported clearance issues. I can also create the correct IP67 USB-C footprint directly from the manufacturer datasheet, reposition it, and resolve the charger/fuel-gauge footprint and routing issues while maintaining proper thermal-pad clearance. You will receive the updated KiCad project, BOM/CPL, written review notes, and a fresh DRC report ready for fabrication. Give me one opportunity to handle your project. I assure you of accurate, professional work and timely delivery. I can start immediately and complete the scope within your 1–2 week timeframe.

@milanc46

KiCad 10 | 4-Layer PCB | ESP32-S3 | JLCPCB Hi there, I understand you need an independent review and finalization of the existing 4-layer ESP32-S3 sensor board, including the USB-C footprint and charger/fuel-gauge placement issues. Tech Stack: ■ KiCad 10.x ■ ESP32-S3 / Embedded Hardware ■ 4-Layer Mixed-Signal PCB ■ Battery Charging & Power Management ■ USB-C / I2C / ESD Protection ■ JLCPCB DFM/DRC My Approach: ■ Review schematic, power, USB-C, I2C, protection, antenna keep-outs and DRC findings. ■ Create the correct IP67 USB-C footprint and re-route as required. ■ Resolve charger/fuel-gauge placement and thermal-pad clearance. ■ Re-run DRC and finalize BOM/CPL for JLCPCB. Guarantee: ■ Fabrication-ready KiCad project ■ Verified footprints and routing ■ Final DRC report ■ Clear review notes Let's connect and review the existing KiCad files and open items so I can propose the right approach and turnaround. Regards, Milan

@nehavaddellu

As an Electronics & Communication Engineer with hands-on multi-layer layout experience, I am ready to validate and finalize your 4-layer sensor board. My background in hardware R&D makes me uniquely suited to execute the USB-C pad swap and maintain strict signal integrity near sensitive antenna and battery-charging zones. Working directly in KiCad, I will create datasheet-accurate footprints, resolve routing/clearance issues, and run thorough DRC checks to guarantee a board that is fully optimized for manufacturing. Over a 1–2 week sprint, I will deliver production-ready KiCad files, updated BOM and CPL files, defined keep-out zones, and a detailed review note outlining every design adjustment made.

@bhargav922002

Hello, I’m Bhargav, bringing 10 years of experience in Electrical Engineering with extensive expertise in PCB design and validation tailored to your needs. I understand you require someone to finish and validate a 4-layer sensor board built around an ESP32-S3 module. My approach includes a thorough design review, ensuring the power architecture, USB-C footprint swap, and battery charger placements are executed flawlessly. I will provide a detailed report documenting any changes and confirming DRC compliance before sending it off for fabrication. Let’s start a chat to discuss your project in detail and ensure all aspects are addressed. Best regards, bhargav922002

@mrravianh

Hi i can help you in your project i have multiple years of experience in high speed pcb design and jlcpcb