ESP32 RS-485/MODBUS firmware for sensor interface

Käynnissä Julkaistu 3 vuotta sitten Maksettu toimituksen yhteydessä

£20-250 GBP

Maksettu toimituksen yhteydessä

Käynnissä Maksettu toimituksen yhteydessä

We have an environmental control system which currently uses i2c sensors for temperature and moisture. We would like to change this to RS-485 sensors. Our microcontroller is ESP32-WROOM32E. Our development environment is Arduino IDE.

We are going to use these sensors ([login to view URL]) and require firmware on our main board to interface with them. We require classes or methods for our main firmware routine to call "getTemperature" and "getMoisture" which will return the temperature in degrees C, and the moisture in a format that the sensor can deliver easily.

The firmware produced by this project will need to run stand-alone on an ESP32 dev kit (with a serial break-out such as MAX485) for us to test the new sensors, and then we will later incorporate it into our own firmware and PCB.

We will run two (or more) sensors on the same serial bus, each sensor will be programmed with two separate addresses.

Testing: It would be best if you can confirm a working solution with your own hardware (ESP32 dev kit, break out board and a sensor simulator), or if that is not possible, provide a firmware solution for us to test here where we already have the hardware.

Summary: Write stand alone Arduino-compatible firmware for ESP32 to interface with multiple RS485 sensors.

Elektroniikka Mikrocontroller Arduino Sähkötekniikka

Projektin tunnus: #29034804

Tietoa projektista

7 ehdotusta Etäprojekti Aktiivinen 3 vuotta sitten

Haluatko ansaita rahaa?

Freelancerin tarjouskilpailun edut

Aseta budjettisi ja aikataulu
Saa maksu työstäsi
Hahmottele tarjouksesi
Rekisteröinti ja töihin tarjoaminen on ilmaista

7 freelanceria on tarjonnut keskimäärin £195 tähän työhön

Käyttäjän sagradoamicus profiilikuva
sagradoamicus

Hi I am experienced electronics engineer with more than 14 years of experience. I have read the details and would like to know more about it. Please get in touch to discuss it further Regards

£400 GBP 5 päivässä
(263 arvostelua)
8.0
Käyttäjän nikitamorozzz profiilikuva
nikitamorozzz

Hi I am an firmware developer who are familiar with arduino and C programming. In the past I have developed the various sensors for smart greenhouse. I can provide you nice code for converting to RS485. Looking forwar Lisää

£150 GBP 7 päivässä
(32 arvostelua)
5.7
Käyttäjän bulgar profiilikuva
bulgar

Dear Sir, We are a small R & D company, based in Bulgaria, Europe. We specialize in developing Embed systems based ST(STM32), Microchip (Atmel )(PICs,AVR,Atmel ARM) and TI (MSP430) MCPUs and peripheries. For our mobi Lisää

£195 GBP 15 päivässä
(10 arvostelua)
5.5
Käyttäjän laxyroad profiilikuva
laxyroad

Hello. I read your project carefully, and I am very interest in the project. I have developed many temperature and moisture sensors with I2C and RS485. Especially I have been programming ESP32 firmware for over 5 years Lisää

£150 GBP 7 päivässä
(1 arvostelu)
3.7
Käyttäjän Abhi78331 profiilikuva
Abhi78331

Hello sir I have read your requirements and got very much idea what you exactly wants i am an experienced IoT developer with good knowledge of the arduino and sensor. I can help you out with the project Let discuss mor Lisää

£222 GBP 10 päivässä
(4 arvostelua)
3.5
Käyttäjän AngieJonez profiilikuva
AngieJonez

MASTERS IN SOFTWARE DEVELOPMENT AN EXPERT IN ELECTRONICS, MICROCONTROLLER, ELECTRICAL ENGINEERING, ARDUINO Hello employer, I have keenly read and understood your CLEARLY stated instructions. I am qualified since i pos Lisää

£135 GBP 1 päivässä
(0 arvostelua)
0.0
Käyttäjän rafihathbd profiilikuva
rafihathbd

Could not resist but bid on the project! Greetings, with 4 years of experience in esp32 and arduino development i am here to help you with your project. Previously i have developed a professional EMS(Environment Monito Lisää

£110 GBP 4 päivässä
(1 arvostelu)
0.2
Ilmoita samanlainen projekti