Find Jobs
Hire Freelancers

Design an NMEA2000 interface PCB

$250-750 USD

Suljettu
Julkaistu lähes 7 vuotta sitten

$250-750 USD

Maksettu toimituksen yhteydessä
This project is to ultimately create an NMEA interface board that will take signals from a boat Rev Counter, Temperate, Pressure, Fuel level, Leg Position. Ideally a single product that can be programmed to be configured to take any of the signals. Possible that one product be designed that takes all of them as one. The first stage of the project is to look at feasibility and material cost. Second stage would be to produce a prototype.
Projektin tunnus (ID): 13595653

Tietoa projektista

24 ehdotukset
Etäprojekti
Aktiivinen 7 vuotta sitten

Haluatko ansaita rahaa?

Freelancerin tarjouskilpailun edut

Aseta budjettisi ja aikataulu
Saa maksu työstäsi
Kuvaile ehdotustasi
Rekisteröinti ja töihin tarjoaminen on ilmaista
24 freelancerit tarjoavat keskimäärin $603 USD tätä projektia
Käyttäjän avatar
Dear Sir, If you are looking for an highly skilled hardware engineer, I believe that I am the one who you're looking for. I am also an experienced PCB designer who has over 16 years design experience on complex PCB design. I can provide you with design service from schematic entry(circuit design) to PCB layout. I can help you prototype the PCB. Clients' highly satisfied testimonials can be found in my feedbacks. Please message me if you are interested in my service. We can talk more. I would not disappoint you if you select my service. EDA Tools--ALTIUM, ORCAD, PADS, EAGLE.
$700 USD 10 päivässä
4,9 (110 arvostelua)
8,3
8,3
Käyttäjän avatar
Hi Sir I am an expert electronics engineer with more than 8 years of experience in board designs I can do it for you I have more than 8 years of experience in this field. Please have a look at my profile I assure you quality work and on time delivery I am waiting for your reply to start Regards
$400 USD 10 päivässä
4,9 (218 arvostelua)
7,9
7,9
Käyttäjän avatar
Hi, I am a post graduate power electronics engineer and having very good experience in product design and development. I am excellent in embedded programming using pic, dspic controllers and MATLAB codding for Power projects, Boot loaders, CAN communication, EEprom. UART , Protocols for networking, wi-Fi routers, Electrical vehicles and AC drives controls. I designed sine wave inverters for standalone and grid tie Inverters. I designed projects like Off line UPS up to 3 KVA, synchronous rectifiers, Solar MPPT chargers, Battery chargers ,Grid tie inverters design with PLL and feedback control circuit emergency light of 66W and Online UPS control cards, Battery Charging power supplies, LED drivers for PWM controlling and dimming, SMPS, Power supplies. I have experience in schematics and PCB design experience in Altium and ORCAD. I am ready to work for you. Please contact for further discussion.
$1 666 USD 30 päivässä
4,8 (51 arvostelua)
6,5
6,5
Käyttäjän avatar
Hi sir not problem with design any mini module with NMEA protocol you can start design witn standar modules GPS low cost and next design your PCB with full functions. Best Regards. Miky
$555 USD 10 päivässä
4,9 (50 arvostelua)
6,4
6,4
Käyttäjän avatar
Hello, Have a great day. We are a startup company offering design and prototyping services. We will provide complete documentation for required hardware at this stage. Please feel free to contact us. Best Regards, Shahbaz.
$700 USD 10 päivässä
4,6 (44 arvostelua)
6,9
6,9
Käyttäjän avatar
Hi Sir, We are professionals who do expert designs in circuits and pcb layouts. we are qualified engineers and take things from start to end product without compromising the quality. We offer our services at very feasible rates. Please discuss with us in details. We are team of developers and engineers professional in designing electronic circuit solutions, pcb designs, database programming such as MySQL etc, software designs and GUI/UI development, android applications, integrating software and hardware and providing complete solutions. In this bid, we offer you our solution at very low and affordable rates based on your desired requirements. we normally follow several checks to ensure the quality of service and products. In this bid prototyping is not included, if at certain point you would like to have prototypes manufactured, we can provide you at minimal cost including courier charges (DHL/FedX etc). We, very humbly deal with our clients and provide technical support to them during all phases of project execution. We are very much looking forward to hear from you in coming days. Cheers, Ahmad Lead Technical Engineer Turktronics Inc. An Internet of Things Company
$250 USD 12 päivässä
4,8 (33 arvostelua)
6,4
6,4
Käyttäjän avatar
Hello! I am interested in your offer! I have experience in PCB layout (over 10 years in Altium Designer, Eagle CAD, OrCAD and others) for power electronics with microprocessors PIC (microchip), AVR (ATMEL), Arduino, STM32 (STeleсtronics) and others. Examples of my work you can see in the portfolio Waiting for your reply. Best regards, Denis Mark.
$250 USD 10 päivässä
4,7 (37 arvostelua)
6,2
6,2
Käyttäjän avatar
Hi, I hope you are doing well. I have expertise in embedded system design and development. I have worked on all communication protocols of microcontroller to interface sensor and actuators and develop an automated system. I have understood your project requirements and I would like to discuss it in more details. Looking Forward, Khawaja
$526 USD 10 päivässä
4,8 (40 arvostelua)
6,1
6,1
Käyttäjän avatar
Bid Summmary C, C++, VB3, VB4, VB5, VB6, VB, VB.NET 2015, ASP.NET, MVC, WPF, XML, MSSQL 2014, HTML & CSS3, AWS(Amazon Web Service) programmer. Experience on digital and analog electronics for 15 and 25 years...
$750 USD 45 päivässä
5,0 (7 arvostelua)
5,4
5,4
Käyttäjän avatar
A proposal has not yet been provided
$833 USD 15 päivässä
4,8 (6 arvostelua)
4,6
4,6
Käyttäjän avatar
Dear, I can make such device. I have long experience in design and manufacturing of electronic devices. I can also assembly and test device. All the best, Miroslav
$450 USD 15 päivässä
5,0 (2 arvostelua)
4,2
4,2
Käyttäjän avatar
1 ) I have over 10 year experience of PCB Layout / Hardware / EMI / Firmware designs, we can complete various design and layout requirements. # 8051’s MCU / ARM Embedded system / Arduino / ST32FX / IM6x / AVR etc # WIFI / BT / BLE / GPS # LCD / DTV / MD / Web Camera # LED / Lighting # LCD Inverter / Touch ... PCB design and layout. # NIC / LAN # IOT / NRF52832 / ESP8266 # Battery / Solar Charger 2 ) I can use as below to design and layout. # Altium / Protel99SE # Eagle # PADS # KiCad # OrCad / Allegro # Proteus 3 ) I can communicate well in English, please contact us by e-mail or Skype me (saludpcb) to find out relevant details. 4 ) I also have to provide PCB layout design service ( super low price ) # For PCB layout: 2 ~ 4 Layers -> $0.4 ~ 0.6 USD per pad, 6 ~ up Layers -> $0.8 ~ 0.8up USD per pad. # For reprinting of schematic and component, quotation will vary by each case. # A minimal of $100 USD 2L / $200 USD 4L / $300 USD 6L will be charged for each case. What I can do are: # 1,2, 3, 4, 6, 8, .... layers ( PCB / FPCB ) # High Speed and High Density PCB layout # Differential Signal PCB layout # RF Signal PCB layout # 3D Models / Freecad
$555 USD 10 päivässä
4,9 (6 arvostelua)
3,9
3,9
Käyttäjän avatar
Dear sir, We sonen engineer solutions provide Design, Manufacturing and consultancy services to Mechanical, Electrical and Electronic industries, we have qualified designers we support for design and development support case to case basis. our expertise is CAD/CAM/CAE ,PCB Design and development. i have 17 years of experience in product design, and development, worked on electromagnetic product design. please send us the details. Thanks Uday
$777 USD 10 päivässä
4,4 (4 arvostelua)
4,4
4,4
Käyttäjän avatar
Hello I am very excited of this project and would like to jump into cost calculations :) Are there any enclosure standards that you need to follow? Water resistant, dust resistant etc?
$300 USD 14 päivässä
4,8 (7 arvostelua)
4,0
4,0
Käyttäjän avatar
Hello, I am an experienced writer and a mechatronics engineer from a top engineering university in Pakistan. I have completed more than 800 projects and i have over 185 positive reviews in my profile. i shall deliver you quality work. I have a team of writers. Please discuss in details. Regards. Tabeer
$611 USD 10 päivässä
5,0 (1 arvostelu)
2,9
2,9
Käyttäjän avatar
Hello, how are you? I hope you have a bright day/evening from your side. I have read the details provided, but please contact me so that we can discuss more on the project. I believe I have the required skills in this case. I will work on your requirements personally since I do not outsource to third parties, this guarantees you high-quality work that is delivered on time. You can also request for revisions till you’re fully satisfied with the work. I believe writing is a passion and not a money making business where people will deliver low-quality work just to get paid. Try my services, and you will never regret. Waiting for your kind response
$526 USD 10 päivässä
2,3 (3 arvostelua)
3,3
3,3
Käyttäjän avatar
Hello, I have experience with marine electronics (see my portfolio -- e.g., BNWAS using CAN to connect the panel unit with the base unit, and accepted NMEA 0183 from various equipment such as GPS, autopilot, etc.) which passed strict international certifications (wheel mark) on first attempt at Germanischer Lloyd and others. If interested in discussing your project details further, please contact me. Thank you.
$1 000 USD 40 päivässä
0,0 (0 arvostelua)
0,0
0,0
Käyttäjän avatar
A proposal has not yet been provided
$600 USD 15 päivässä
0,0 (0 arvostelua)
0,0
0,0
Käyttäjän avatar
Hello. I am very interested in your project and confident that I am totally capable of doing it. Before being awarded, I would like to discuss it a little further to see exactly what you need. To be clear, my bid doesn't include producing the prototype.
$700 USD 15 päivässä
0,0 (0 arvostelua)
0,0
0,0
Käyttäjän avatar
A proposal has not yet been provided
$277 USD 10 päivässä
0,0 (0 arvostelua)
0,0
0,0

Tietoja asiakkaasta

Maan UNITED KINGDOM lippu
West Wittering, United Kingdom
5,0
32
Maksutapa vahvistettu
Liittynyt maalisk. 16, 2007

Asiakkaan vahvistus

Kiitos! Olemme lähettäneet sinulle sähköpostitse linkin, jolla voit lunastaa ilmaisen krediittisi.
Jotain meni pieleen lähetettäessä sähköpostiasi. Yritä uudelleen.
Rekisteröitynyttä käyttäjää Ilmoitettua työtä yhteensä
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Ladataan esikatselua
Lupa myönnetty Geolocation.
Kirjautumisistuntosi on vanhentunut ja sinut on kirjattu ulos. Kirjaudu uudelleen sisään.