Build me Keypad & Mouse combo -- 2

Suljettu Julkaistu 3 vuotta sitten Maksettu toimituksen yhteydessä
Suljettu Maksettu toimituksen yhteydessä

Looking for anyone who can help in my project to create my first prototype with following

 

Our device consiting two parts, LHS (keypad/keyboard) & RHS (mouse).

8 buttons are present on both sides with their respective provided controls in the button layout pdf file.

There are two buttons present in LHS i.e."G" (when we press analog stick) & "I" (Letter I for India ) & one button "Q" in RHS has its unique feature which I'm referring to as simulation. They change the function of many buttons present on both side LHS & RHS like

When we press a button with an assigned simulation feature i.e. Q, G & I, there has to be a 30ms depress time after which function for all the buttons has been changed and Q stops functioning until we release our finger from the tactile switch. Now as we enter into simulation +1, the function of all the buttons will be similar to provided document under Page +1 where two buttons in LHS perform the function of two buttons simultaneously under each button as provided & 3 buttons in RHS respectively. Similarly in other simulations.

How buttons with underline perform their function and changing all the buttons to default or previous page? They will make a 30ms depress time after which function for all the buttons has been changed and pressed button stopped working until we press it again with updated controls following buttons must change settings to the default page for all the buttons as they are present in all simulations. "4 in LHS & 3 scroll wheel up with 5 scroll wheel press in RHS"If we went into a simulation under simulation then right after pressing the following buttons all the settings has to be changed to default settings

All the buttons other than simulation buttons must function as provided in the video below which shows real depress time as we hold any button for its respective purpose

The mouse sensor I would like to use in RHS is Pixart ADNS-3050

I would like to work by following milestones:

Hardware Design is divided into 3 milestones (Schematic + PCB layout + Gerber & BOM) to manufacture the Prototype

4th Milestone would be Firmware Coding(MCU code where will be used in the project)

5th Milestone: Prototyping and Testing(make the prototype and test the prototype with the firmware code) + Shipment of a working prototype in 3D enclosure

Elektroniikka Mikrocontroller Piirilevyn asettelu Arduino Piirisuunnittelu

Projektin tunnus: #29063279

Tietoa projektista

9 ehdotusta Etäprojekti Aktiivinen 3 vuotta sitten

9 freelanceria on tarjonnut keskimäärin ₹145556 tähän työhön

avigupta0061

Best PCB Design Expert at your doorstep! Dear Client, We can help in your project to create prototype Please share me your schematic and I have seen the images and pdf and could do it for you. We couldn’t stop ourselv Lisää

₹112500 INR 2 päivässä
(33 arvostelua)
7.1
HarimohanG

Dear Client, I can help create your first prototype. I can build your Keypad Mouse combo as per your requirements. I have read and understood your requirements and could do it for you in the least time and utmost supe Lisää

₹112500 INR 2 päivässä
(3 arvostelua)
5.2
maheswar17031

Dear Employer, I am an Electronics Engineer, Programmer, PCB designer and an expert in Arduino programming. I can do this project. I did almost 100+ projects till now. I am an expert in PCB designing also. I did many P Lisää

₹125000 INR 30 päivässä
(34 arvostelua)
5.0
doggar302

Hi! I am an Electronic engineer, PCB Layout, Circuit Design, microcontroller, STM32 microcontroller, C programming expert having past experiences with ,Altium, arduino, pic, AVR, chipkit and Texas instruments microcont Lisää

₹150000 INR 29 päivässä
(10 arvostelua)
4.7
PathumSudarshana

Dear Sir, So we can design this project in this way... We can use a Arduino Leonardo Board as main board because it can be use as an plug and play device... So it is the most Suitable Brain to this project... Of course Lisää

₹75000 INR 15 päivässä
(16 arvostelua)
3.5
writiqueproject

ELECTRICAL As an electronic architect, I have been working in PCB structure/design and firmware programming field for 8+ years. Here is a portion of the encounters that I worked back. - Schematic and PCB Format is uti Lisää

₹150000 INR 7 päivässä
(7 arvostelua)
3.4
ns534712

Dear Sir/Madam I have 3+years of experience in Software development and Hardware Design. I have completed more than 10 industrial projects. My skills are:- Programming- MATLAB, LabVIEW, Python, and C/C++. PCB Tool- A Lisää

₹150000 INR 10 päivässä
(1 arvostelu)
1.0