Suoritettu

RS485 Arduino INO

ok thanks

Hi I have a ItsyBitsy M0 Express. I want to connect a RS485 Halfduplex with just the 2 wires A and B. I have connected a converter wich makes out of the differntial signal of the AB RX/TX. I have just left the MISO and MOSI pins. The connected part just sends 2 bytes after it received 2 bytes from ItsyBitsy, can you send me just such an INO code? Let me know how much it costs. Thanks Franz

Taidot: Arduino, elektroniikka, Mikrocontroller

Näytä lisää: tx rx hdmi cat5e, arduino ethernet rs485, rs485 arduino, arduino rs485 modbus, arduino rs485 network, arduino rs485 full duplex, arduino rs485 project, arduino rs485 schematic, arduino rs485 protocol, arduino rs485 shield, rs485 arduino nano, receive rs485 arduino, communicate rs485 arduino, rs485 arduino pcb, schematic rs485 arduino, arduino ino, arduino ino pde, send code arduino web, pwm rs485 arduino, i have 3 very simple webpage designs but i have lost the psd for them i need someone to redo it and send me the psd file

Tietoa työnantajasta:
( 8 arvostelua ) Embrach, Switzerland

Projektin tunnus: #18200584

Myönnetty käyttäjälle:

tifoda

Hello. Im designing different electronics devices, mostly based on avr, arm MCUs and boards with them like arduino, stm-discovery etc. (autopromotion^)) You want to connect rs-485 to arduino, have some 485 bus dri Lisää

$30 USD 1 päivässä
(28 Arvostelua)
5.2

9 freelanceria on tarjonnut keskimäärin %project_bid_stats_avg_sub_26% %project_currencyDetails_sign_sub_27% tähän työhön

xiaoqideng

Dear, Client. Thanks for your proposal. I did read your detail. I am very interesting to your job. I am an expert and developer who have rich development experiences in many jobs with Arduino, RS-485 communicatio Lisää

$40 USD 1 päivässä
(21 arvostelua)
5.2
xiaoguang2018

Hello. I have a experience for arduino communication. the RS485 is serial communication. the important is control for select RX/TX. how do you connect the converter? and what is MOSI and MISO left? Regards.

$30 USD 1 päivässä
(21 arvostelua)
4.9
arrijal1992

Hi, can you send me your wiring diagram? I guess the problem with RS485 transciever is it contain control pin to set wether it will be used as sender / receiver. I have used RS485 for several project, so I know it's co Lisää

$30 USD 1 päivässä
(23 arvostelua)
4.6
sikanderabbas48

I am an Electrical Engineer having specialization in Electronics Control and Power, teaching at well known University in Pakistan. I have my BS degree in Electrical Engineering with specialization in Power. Also i hir Lisää

$20 USD 1 päivässä
(2 arvostelua)
1.1
teknoteam

HI, I think you can use a basic test I've used with RS 232, RS 485 should "just" change the physical layer, not the logic. The software is very easy, I cannot bid for less because minimum bid is limited by freela Lisää

$15 USD 0 päivässä
(1 arvostelu)
0.7
saygins

Hi you should connect #0 and #1 pin for serial Rx and Tx "SCK/MOSI/MISO - These are the hardware SPI pins" also you connect the rs485 converter de/re pin to gpio output to set direction

$30 USD 1 päivässä
(1 arvostelu)
0.0
shahzain93

Hey man, I can do that, Have 3 years experience in electronics. thanks

$80 USD 10 päivässä
(0 arvostelua)
3.1
aymos

hello dear i think you have to use serial port of arduino not the spi, also do you use max485 as a converter AB/RS232 ? finally you can find many exemple in arduino ide select : file > exemples thanks aymen

$25 USD 1 päivässä
(0 arvostelua)
0.0