Suljettu

I would like to hire an Electrical Engineer

Purpose:

The purpose of this document is to provide a general description of deliverables and expectations associated with the design of electrical schematics for a processing and conveying line.

Scope:

Electrical Engineer will design electrical schematics for a processing and bag conveying system designed to handle 40 lb bags of salt. See attached drawing for details and specifications. All incoming system power will be supplied to a single electrical cabinet and power (both 440 volt / 3 phase for motors and 110 volt for controls) will be distributed to the entire system from this panel. No secondary power source is allowed for any of this supply.

Deliverables:

• All electrical components shall be rated for 480v, 3 phase, 60 Hz service. All control panels shall be constructed with 100% UL approved components. Each enclosure shall be designed to meet at a minimum NEMA 4x or IP56 requirements. All wiring and controls shall be installed in the cabinets, properly supported, wires properly routed and numbered.

• All electrical panels shall be constructed from materials suitable for continuous operation in corrosive environments.

• Technical documents and manuals will be provided as part of the deliverables for all components used in association with the packaging and handling system. They include but are not limited to electrical system panel layouts, wiring schematics and pneumatic schematics

Description of the Equipment Serviced by this Panel

Net weigh filler - (5511 Weight Controller and Solenoid Powered; Qty 3) - 110 Volt - [login to view URL]

Bin Level Sensors (Qty 3) - Hi / Lo / Lo Level Inhibit - 110 Volt - [login to view URL]

Bag take-away conveyor - 1 HP -

Bandrite Model 6000 Bag sealer - 110 Volt (23 Amps) - [login to view URL]

Pnuematic Bag kicker (Solenoid Powered; Qty 1) - 110 Volt

Incline conveyor - 1 HP -

Electrical Engineer will provide electrical wiring schematics and panel layouts including:

4-button pushbutton station to be located at filler area; Start, Stop, Manual Dump, E-Stop

1-button pushbutton station to be located at bag stacking station for E-Stop

Motor control panel in polycarbonate 4X enclosure; Fused disconnect, 2 motor starters, relay logic

5 kVA transformer; 480VAC to 120VAC 50 Amp output in Type 4X polycarbonate enclosure

The motor control panel will be wired with an input for 480VAC 60 Amp supply. This power will route through a 3-pole fused disconnect, then distributed to the motor starters and their overloads, and to output terminals to connect to the transformer. The 120VAC output of the transformer will be routed back into the motor control panel, passing through 2 different circuit breakers and to terminals. Breakers are 1 dedicated for the heat sealer, the other for all other 120VAC devices.

8 ga. wire will be used from the motor control panel to the heat sealer. All other AC wiring can be 16 or 14 ga.

As the equipment will be broken down for shipment we require junction boxes between the following points of the system:

At the Gravity Net Weigher power to the 5511 controls

At the take-away conveyor; one for 120VAC and another for the 480 VAC

At the incline conveyor; one for 120VAC (e-stop) and another for the 480VAC

At the Supply Bin with Wiring Between 5511 Controller and Lo Level Inhibit Sensor

At the Supply Bin with Wiring from Hi / Lo Sensors to Junction Box Terminals (Final Field Wiring to be Completed by Customer to Their Up Stream Process Feeding Equipment)

Motor Control Hardware to be Shown on Layouts and Schematics:

20” high x 24” wide x 8” deep Polycarbonate Type 4X motor control panel

25% extra room in panel for future expansion

Mounted to SS rack to raise off the floor

Front panel lockable disconnect handle

Front panel E-Stop & Hand-Off-Auto switch

60 Amp 3-Pole fused disconnect

Two 1 Hp. rated 3-phase motor starters with overload protectors

Relays, terminals, circuit breakers, etc., as required

1-Hole PB enclosure with E-Stop switch

4-Hole PB enclosure with E-Stop, Start, Stop & Manual Dump

5 kVA 480-120 Transformer in polycarbonate Type 4X enclosure Includes:

Hi / Lo / Lo Level Inhibit Level Sensors -

Taidot: Piirisuunnittelu, sähkötekniikka, valmistus, tuotesuunnittelu

Näytä lisää: where can i get a chemical engineer for hire in sa, mechanical electrical engineer for hire, indian electrical engineer for hire, electrical engineer for hire, electrical engineer for hire south africa, cisco engineer for hire, chip design engineer for hire, chemical engineer for hire, cad engineer for hire, biomedical engineer for hire fort worth texas, audio engineer for hire, asian engineer for hire, aircraft maintenance engineer for hire, hire appointment setters final expense, licensed engineer electrical, eplan engineer electrical jobs

Tietoa työnantajasta:
( 0 arvostelua ) United States

Projektin tunnus: #13978089

7 freelanceria on tarjonnut keskimäärin %project_bid_stats_avg_sub_26% %project_currencyDetails_sign_sub_27% tähän työhön

$1111 USD 20 päivässä
(6 arvostelua)
4.3
marcellomessias

Engineering Drafting - 3D Model - Product Design Envisioned Engineering OUR GOAL IS BRING TO LIFE YOUR IDEA. Performing Engineering Solutions to most variable disciplines, Creative Solutions and Product Design. Lisää

$1000 USD 30 päivässä
(7 arvostelua)
4.6
Valuesolutions

Hello, how are you? I hope you have a bright day/evening from your side. I have read the details provided, but please contact me so that we can discuss more on the project. I believe I have the required skills in this Lisää

$250 USD 5 päivässä
(6 arvostelua)
4.1
chyconsl

Hi, Can we discuss the project further? I have done similar project and understood the project outline. Please give me a chance. A trial will convince you. Looking forward to work with you.

$555 USD 10 päivässä
(3 arvostelua)
2.8
$777 USD 15 päivässä
(1 arvostelu)
2.1
$777 USD 10 päivässä
(0 arvostelua)
0.0
goldsea808

[login to view URL] (pi, pi camera) [login to view URL] (pi, recognizing signs) [login to view URL] (Pi, Line follower, Sensor) [login to view URL] ( Lisää

$555 USD 10 päivässä
(0 arvostelua)
0.0