Suoritettu

Arduino code -- 2

Project Scope:

Program an Arduino and (1) provide the code, as well as the (2) wiring diagram, to instruct a stepper motor to rise via remote, then lower upon receiving a signal from a sensor or within a certain timeframe if the sensor is not triggered.

Device Functionality:

The device will raise and lower an arm 90 degrees using a gear attached to a stepper motor. The arm will be raised by pressing a button on an IR remote. Once raised, the arm will remain raised until a sensor attached to the arm senses an impact above a certain threshold OR until a period of 10 seconds has passed. Once the sensor is activated OR 10 seconds pass, the arm will be lowered back to the start position.

Modules:

A. From down position:

Push button, IR remote // signal

Stepper motor up // arm goes up from 0 degrees to 90 degrees

Timer // 10 second timer begins

B. From up position:

“Impact” case scenario:

Vibration Sensor // feels “impact” above an adjustable threshold

Serial register // “impact”

Green LED lights up // displays “impact”

Stepper motor down // result of impact; stepper motor goes down from 90 degrees to 0 degrees

Timer // timer stops

OR

“No Impact” case scenario:

Timer registers time expired// 10 seconds expires

Red LED lights up // displays “no impact”

Serial register // “no impact”

Stepper motor down // arm goes down from 90 degrees to 0 degrees

Components used in the project:

1. Arduino Uno R3 (RexQualis)

2. Breadboard

3. RexQualis Breadboard Power Supply Module

4. RexQualis IR remote

5. Impact sensor:

a. SW-420 vibration sensor module OR

b. MPU-6050 3 axis Accelerometer/ Gyrometer

6. 28BYJ-48 5 volt Stepper Motor

7. ULN2003 stepper motor driver board

8. Green and Red LEDs

9. Wires and resistors as necessary

Deliverables:

1. Arduino code for the requested tasks in a .TXT and/ or .INO file format

2. Schematic similar to the attached file:

Deadline:

Four business days from selection

Taidot: Arduino, sähkötekniikka, elektroniikka

Näytä lisää: convert arduino code, polar heart arduino code, arduino code reader, arduino for loop, arduino delay, while loop arduino, arduino help, arduino reference, arduino functions, arduino millis, arduino array, wifly arduino code, heart monitor arduino code, digimatic arduino code, arduino code power monitoring relay, wire arduino code, arduino code linear actuator control, magnetic reader arduino code, arduino power meter project, reading digital callipers arduino code

Tietoa työnantajasta:
( 1 arvostelu ) Springfield, United States

Projektin tunnus: #17944217

Myönnetty käyttäjälle:

HaiderJutt007

Hello there, I am an Electrical Engineer by profession and have been doing Arduino related projects for a while now. I have worked with all the equipment you have mentioned in the description and got the expertise you Lisää

$78 USD 3 päivässä
(12 Arvostelua)
3.5

22 freelanceria on tarjonnut keskimäärin %project_bid_stats_avg_sub_26% %project_currencyDetails_sign_sub_27% tähän työhön

sagradoamicus

Hi I am experienced electronics engineer with more than 8 years of experience. I have completed a number of projects here. Please review my profile to see the feedback from my previous employers Regards

$155 USD 3 päivässä
(223 arvostelua)
7.8
ahmedmohamed85

Dear sir I have more than 10 years in embedded systems design please check my profile also please message me so that we can discuss best regards

$122 USD 3 päivässä
(195 arvostelua)
7.2
$150 USD 3 päivässä
(31 arvostelua)
6.5
jartur

Hello, I can help you with your Arduino project, but. I need more information about your project, maybe other components, deadline, and other things. Right now I have all components to test it until achieving the pro Lisää

$250 USD 22 päivässä
(88 arvostelua)
5.9
junaidahma463

Hello client i have seen ur project and i believe that i can do it efficiently and within 2 days span. I will provide u schematic as u mentioned. I will help u troubleshooting the wiring and also working of the code. P Lisää

$122 USD 2 päivässä
(43 arvostelua)
5.3
maxbul

I work with Arduino since 2010 and have more than 20 years of experience in programming and electronics. I have all the necessary components (motors, drivers, MPU6050 etc) for prototyping.

$140 USD 4 päivässä
(57 arvostelua)
5.4
xiaoqideng

Dear, Client. Thanks for your proposal. I did read your detail carefully. I am very interesting to your job. I am an expert and developer who have rich development experiences in many projects with Arduino. I am Lisää

$200 USD 7 päivässä
(12 arvostelua)
4.4
RoboTechnics

Hello, I believe I could answer the product development needs of your project in terms of both design and hardware development. I have experience, especially in wearable product development so I have lots of experie Lisää

$155 USD 4 päivässä
(3 arvostelua)
4.6
mos3d

Greeting there , I could absolutely help you with your Arduino project i am very excited work on your project and help you get it done in short time About my experience : [login to view URL] Lisää

$200 USD 2 päivässä
(21 arvostelua)
4.6
Mestek

hello i am a computer engineer,i have masters in computer engineering,i have experience for more than 7 years in arduino and electronics i have read ur description for ur projects and the used parts,and realy it is Lisää

$94 USD 2 päivässä
(9 arvostelua)
3.3
chanchalkks

Hello, I have the experience to work on all the all the components that you mentioned. I will provide you TESTED working Source Codes and connection diagram with proper instructions as per your requirement. I want Lisää

$225 USD 4 päivässä
(13 arvostelua)
3.5
andyf1

Hello! After reading your description, I interested to work with your project. I have all hardware for testing project. And I have enough experience to make project as best as possible Look forward to your answer. Lisää

$111 USD 3 päivässä
(2 arvostelua)
1.0
$170 USD 7 päivässä
(3 arvostelua)
0.7
MathsMasterA

Very interesting project. I can complete your project in time. Sure. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

$150 USD 3 päivässä
(1 arvostelu)
0.6
rwhitesnow125

Hello there How are you? As a professional electrical engineering expert with more than 7 years of experience, I am very confident to complete your project successfully. I have rich experience in programming steppe Lisää

$155 USD 3 päivässä
(0 arvostelua)
0.0
$166 USD 7 päivässä
(0 arvostelua)
0.0
DevStar925

Dear Employer, How are you? As you can see in my profile, I have great experience in C/C++, C#, and Java programming as well as Microcontroller. Especially, I have completed many Raspberry Pi and Arduino projects and Lisää

$150 USD 3 päivässä
(0 arvostelua)
0.0
Elektrische

I can do your project and as my first job I’ll give you a pcb design for your project for free and if you explain me more about it I’ll can make you some recommendation of improvement .

$111 USD 6 päivässä
(0 arvostelua)
0.0
technoowl

Hello I am a mechatronics engineer and have experience in working with Arduino based projects and can provide you the code as per requirement. if interested please message me back thank you

$111 USD 15 päivässä
(0 arvostelua)
0.0
$100 USD 4 päivässä
(0 arvostelua)
0.0