
Closed
Posted
Paid on delivery
I have a custom circuit already wired up on an ElectroCookie prototyping board, but it refuses to behave the way the schematic says it should. I need a seasoned set of eyes and hands to track down the fault, correct it, and prove the board works reliably afterward. Here’s what I expect from you: • Inspect the existing ElectroCookie layout, trace connections, and identify any wiring or component errors. • Suggest and implement the fixes—whether that means swapping components, re-routing jumpers, or revising the layout. • Verify the repair with scope or multimeter readings and a short video or photo set that shows the circuit running as intended. • Provide an updated schematic (KiCad, Eagle, Altium, or even a clear hand-drawn PDF) that reflects the final, working design, plus a brief fault-analysis note so I know what went wrong. If you are comfortable probing live boards, reading datasheets on the fly, and know the quirks of the ElectroCookie platform, this should be a quick turnaround job.
Project ID: 40785692
54 proposals
Remote project
Active 4 days ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
54 freelancers are bidding on average $138 USD for this job

Hi, I have experience in designing Circuits and can complete your project. I have expertise in the following: 1- Designing schematic and PCBA 2- Ordering the PCBA and getting boards manufactured. 3- Writing firmware for the PCBA to make sure everything works as expected. 4- I can also develop smartphone apps to communicate and control the hardware. If you wish we can discuss in chat. Thank you.
$140 USD in 7 days
7.5
7.5

Troubleshooting a malfunctioning prototyping circuit requires both hands-on electronics work and the ability to compare real signals with the intended design. My background spans analog design, electronic design, power electronics, embedded systems, and PCB layout, giving me the practical range needed to trace wiring, component, and signal-path faults on your ElectroCookie board. I can inspect the existing layout against the schematic, identify incorrect connections or components, and implement suitable corrections. My experience includes analog filters, op-amp circuits, AC/DC and DC/DC converters, battery chargers, motor-drive electronics, RF devices, and embedded platforms including ESP32, PIC, STM32, Arduino, and DSP systems. I also use Altium, EasyEDA, OrCAD simulation, and MATLAB, so I can provide an updated schematic and a clear fault-analysis note reflecting the repaired circuit. I am comfortable working with circuit measurements and validating electronic designs through simulation and practical testing. Choose me to debug the board, document the correction, and demonstrate its reliable operation.
$100 USD in 10 days
7.5
7.5

⭐⭐⭐⭐⭐ I can help troubleshoot your ElectroCookie circuit systematically, identify why it differs from the schematic, and verify the repair rather than relying on guesswork. I’d start by reviewing your schematic and inspecting the board layout, checking power rails, component orientation, jumper connections, and critical signal paths. I’d then isolate the fault through targeted multimeter measurements and oscilloscope testing where appropriate, making only the necessary wiring or component changes. Once corrected, I’d verify the circuit’s behavior against the expected operation and document the results with measurement readings and clear photo or video evidence. Deliverables: • Fault diagnosis and implemented corrections • Verification measurements and visual evidence • Updated schematic in an agreed format • Brief fault-analysis report explaining the cause and repair Could you share the original schematic, clear photos of both sides of the board, the expected behavior, and what it currently does instead? Also, please confirm the operating voltage so I can assess the safest troubleshooting approach. With those details, I can estimate the scope and get started efficiently.
$140 USD in 7 days
5.8
5.8

Hi, I'm a senior electronics engineer with over 7 years of experience in circuit design, PCB development, hardware debugging, and prototype testing. I have extensive experience troubleshooting electronic circuits, identifying wiring and component issues, and validating designs using oscilloscopes, multimeters, and other laboratory equipment. For your ElectroCookie prototype, I'll start by comparing the physical wiring against the schematic, checking component orientation, solder joints, jumper connections, power rails, and signal paths. I'll then systematically identify the root cause, recommend the necessary modifications, and verify the corrected circuit through voltage measurements, signal analysis, and functional testing. I can also update the schematic in KiCad and provide a brief technical report explaining the identified problems, implemented fixes, and verification results. If physical testing is required, we can arrange for the prototype to be shipped to me. Could you share the existing schematic, clear photos of both sides of the ElectroCookie board, and a brief description of the circuit's expected behavior versus its current behavior? This will help me assess the troubleshooting scope and estimate the required working time. Best regards, Yaroslav
$140 USD in 7 days
5.7
5.7

Circuit debugging, electrical engineering, and prototyping are core skills I can apply directly to your ElectroCookie board fault. I can inspect the existing wiring against the schematic, trace continuity and signal paths, identify incorrect connections or components, and make the practical corrections needed to restore the intended behaviour. My background in engineering calculations, electronics, embedded systems, PCB layout, and circuit design supports the full task—not only finding the fault, but checking that the repaired circuit operates correctly. I can also provide clear measurement evidence from a multimeter or oscilloscope, supporting photos or a short video, an updated schematic, and a concise fault-analysis note documenting the final design. With more than 150 completed freelance projects since 2014, I am dependable, analytical, and comfortable working through technical problems carefully. Choose me to diagnose and repair the board and document the working result clearly.
$140 USD in 7 days
5.7
5.7

Hello, I can help troubleshoot your ElectroCookie circuit by comparing the actual wiring with the schematic, checking component values and connections, and identifying the fault. I’ll provide a step-by-step debugging plan, recommend the necessary fixes, and update the schematic to reflect the corrected design. I can also document the fault analysis and verification results based on the measurements and testing equipment available. Please share the existing schematic, clear photos of the board from multiple angles, and a description of the expected versus actual behavior so I can assess the issue and estimate the turnaround time.
$140 USD in 7 days
5.6
5.6

Hello, With 15+ years of electronics engineering experience, I can systematically troubleshoot your ElectroCookie prototype and identify why the actual circuit differs from the schematic. My approach is to verify power rails and grounding first, trace each connection against the schematic, check component values and polarity, and measure critical signals using a multimeter and oscilloscope where appropriate. I’ll isolate the root cause before making targeted corrections, then retest the circuit under normal operating conditions. You’ll receive the corrected wiring/layout, an updated schematic in your preferred format, measurement evidence (photos or video), and a concise fault-analysis report documenting the cause and solution. I focus on finding the actual fault—not just making the circuit work temporarily. Best regards, Hamza
$90 USD in 4 days
5.4
5.4

I am an Embedded Systems and PCB Design Engineer with experience in Altium Designer, Kicad, Easyeda, Protious and custom hardware development. I can design your PCB from schematic to production-ready files, including: • Schematic Design • PCB Layout • Component Selection • Design Rule Check (DRC) • Gerber Generation • BOM Preparation • Manufacturing Support (JLCPCB, PCBWay, etc.) I have experience with ESP32, STM32, sensor interfaces, power supplies, RF modules, Ethernet, and industrial electronics. Please share the project requirements, schematic (if available), board dimensions, and any special requirements. I can start immediately. Looking forward to working with you.
$140 USD in 7 days
5.1
5.1

Hi, I can help troubleshoot your circuit by comparing the schematic with the actual wiring, tracing connections, and identifying potential component or wiring faults. I can recommend corrective steps, update the schematic, and prepare a brief fault-analysis report. I can also help verify the expected operation based on available measurements and access to the physical board. You can also check my portfolio for examples of my previous PCB and embedded hardware projects. Could you share the schematic, clear photos of the ElectroCookie board, component list, and a description of the expected versus actual behavior? Best regards, Ahmed
$140 USD in 7 days
4.6
4.6

Hi, I’m an electronics engineer experienced in circuit debugging, PCB design, and embedded hardware development. I can inspect your ElectroCookie setup, trace the connections, identify faulty wiring or components, and verify the fixes using a multimeter or oscilloscope. I’ll also provide an updated schematic and a brief fault analysis documenting the issue and solution. I’m ready to review your circuit and get it working reliably.
$56 USD in 2 days
4.2
4.2

✅✅✅✅✅I’d approach your ElectroCookie circuit systematically, tracing the actual connections against the schematic to identify the fault rather than replacing components unnecessarily. I would begin by reviewing the schematic and board photos, checking power rails, component orientation, jumper connections, and critical signal paths. Using a multimeter and oscilloscope where appropriate, I’d isolate the fault, implement the necessary corrections, and test the circuit against its expected behavior. Once the repair is complete, I’d document the verification measurements and provide clear photo or video evidence of the working circuit. Deliverables: • Fault diagnosis and implemented repairs • Verification measurements and visual evidence • Updated schematic in KiCad, Eagle, Altium, or PDF • A concise report explaining the fault and how it was resolved For a straightforward circuit, I’d target a 1–3 business-day turnaround, depending on complexity and component availability. Could you share the original schematic, clear photos of the board, and a description of the symptoms? Please also include the supply voltage and expected versus actual readings, if available. This will help me assess the fault and recommend the quickest path to a reliable fix.
$140 USD in 7 days
4.4
4.4

Hi, I can troubleshoot your ElectroCookie board, identify wiring or component faults, and repair the circuit to match the schematic. I’ll verify its operation with multimeter or oscilloscope measurements and provide an updated schematic with a clear fault-analysis report and photos of the working board.
$100 USD in 1 day
4.2
4.2

Our RF and electronics engineering background makes us well suited to diagnose a wired circuit that does not match its schematic behavior. We work across circuit design, electronics, embedded systems, and PCB layout, combining theoretical analysis with practical hardware implementation rather than relying on visual inspection alone. We can trace the ElectroCookie connections against the schematic, identify wiring or component mistakes, and apply the required corrections through component changes, jumper rerouting, or layout revisions. Our experience with KiCad, Proteus, and Altium Designer also supports producing a clear updated schematic that accurately reflects the repaired board. We will verify the working circuit using appropriate multimeter or oscilloscope measurements and provide concise fault analysis with supporting photos or video. Choose me for a careful, technically grounded debugging and documentation job.
$300 USD in 7 days
3.6
3.6

Greetings Dear Hiring Manager I can troubleshoot your ElectroCookie circuit, identify wiring faults, and document verified repairs 1. Can you share photos of the board and schematic? 2. What symptoms or unexpected readings occur? 3. What are the supply voltage and key components? 4. Do you have multimeter or oscilloscope measurements? 5. Can you share the expected circuit behavior? I am waiting in chat to discuss your project in more detail Best Regards Dr Kainat
$31 USD in 1 day
3.5
3.5

I have experience in circuit debugging, PCB troubleshooting, component testing, and schematic verification. I can identify wiring faults, test circuits using a multimeter and oscilloscope, and document corrections. I also have a dedicated lab for hardware testing and prototyping. A misbehaving ElectroCookie build usually comes down to a floating ground or a swapped pinout, and I've debugged enough of these to know where to look first. → 10+ years probing live boards, tracing nets, and reading datasheets on the fly → I'll rework the fault, verify with scope/multimeter, and send photo/video proof plus a clean KiCad schematic and fault note
$120 USD in 2 days
3.5
3.5

Your project exactly matches my electronics troubleshooting and circuit design skills, and I am very interested in diagnosing and repairing your ElectroCookie prototype. MY APPROACH I’ll review your schematic and existing board layout, trace the connections, and check component values, polarity, wiring, and possible shorts. I’ll identify the fault, recommend the necessary corrections, and verify circuit operation using appropriate measurement methods. DELIVERABLES Circuit inspection and fault diagnosis Component and wiring corrections Multimeter or oscilloscope verification results Photos or a short video of successful operation Updated schematic in your preferred format Brief fault-analysis and repair report EXPERIENCE I have 8 years of relevant engineering and CAD design experience, with a focus on electronics, PCB design, and technical documentation. TIMELINE & COSy I can confirm the turnaround and price after reviewing the schematic, board photos, and circuit complexity. QUESTION Can you share the schematic, clear photos of both sides of the board, component list, and details of the expected versus actual behavior? Best regards Sidra https://www.freelancer.pk/u/sidratulm20
$60 USD in 3 days
3.2
3.2

Hello. "ELECTROCOOKIE FAULT TRACING AND VERIFIED CIRCUIT REPAIR" - you need to find why the physical board differs from the schematic, correct the fault, and document a reliable working result. I'd start by checking the wiring against the schematic, then verify supply rails, component orientation, and key signal points with a multimeter or oscilloscope as appropriate. After identifying the cause, I'd document the correction, provide an updated schematic, and capture test evidence with a concise fault-analysis note. Can you share the schematic, board photos, and the expected versus actual circuit behavior? Looking forward to working with you.
$140 USD in 7 days
3.0
3.0

Hello, I can help troubleshoot your ElectroCookie circuit by systematically comparing the physical wiring against the schematic and identifying possible connection, component, or power-related faults. My approach would be: 1. Review the schematic, component datasheets, and clear photos of both sides of the ElectroCookie board. 2. Trace the board connections and check for wiring mismatches, incorrect component orientation, missing connections, or unintended shorts. 3. Develop a targeted measurement checklist to isolate the fault. 4. Recommend corrective changes and update the schematic to reflect the corrected design. 5. Review the measurements and test evidence after the corrections are implemented. Before proceeding, I have three questions: - Can you share the schematic and high-resolution photos of both sides of the assembled board? - What is the expected behavior versus the actual behavior? - Are you comfortable performing the physical corrections and taking multimeter/oscilloscope measurements based on my instructions, or do you require hands-on repair at your location? I work with electronic circuit design, PCB development, and schematic verification using KiCad and Altium Designer. I can support the troubleshooting remotely and provide an updated schematic and a concise fault-analysis report. Best regards, Hamza El Amraoui
$200 USD in 10 days
3.1
3.1

Hi, Adelman here from Texas ELECTROCOOKIE CIRCUIT DEBUGGING - you need to find why the wired circuit disagrees with the schematic and verify the fix with real measurements. I’d trace the connections against the schematic, check component values and power rails first, then isolate the faulty stage using voltage and continuity measurements. I’d document the root cause and update the schematic to match the verified circuit. Can you share the schematic, a clear photo of the ElectroCookie board, and the expected versus actual readings? Looking forward to work with you.
$100 USD in 1 day
2.3
2.3

Hi there, Circuit debugging demands practical electronics expertise, and my skills in circuit design, electronics, and PCB layout directly match your ElectroCookie repair. I can inspect the existing wiring against the schematic, trace signal and power paths, and identify incorrect connections, component issues, or layout problems. I can also implement the required corrections, then verify the working circuit with appropriate multimeter and oscilloscope measurements. Alongside the repair, I will provide clear evidence of operation through photos or a short video, an updated schematic, and a concise fault-analysis note documenting what was found and corrected. Best regards, Mobasher Reza
$140 USD in 3 days
2.3
2.3

Huntington Park, United States
Payment method verified
Member since Apr 6, 2012
$250-750 USD
$30-250 USD
$10-30 USD
$10-30 USD
$250-750 USD
$20-500 USD
₹12500-37500 INR
$10-30 USD
₹1500-12500 INR
$30-250 CAD
₹1500-12500 INR
₹600-1500 INR
$250-750 USD
$5000-10000 USD
₹1000-10000 INR
£750-1500 GBP
₹750-1250 INR / hour
₹1500-12500 INR
₹1500-12500 INR
₹1500-12500 INR
$250-750 USD
₹12500-37500 INR
$10-30 USD
$30-250 USD
₹150000-250000 INR