Suljettu

Circuit Board and codee

Hey,

I'm looking currently looking for some one who knows circuit boards how they work and how to assemble them to make what I have added as a picture below. I am looking for them to work on radio frequency (ie like a wireless door bell or car key remote). the second picture below is what i already have including the button sensors for the main board. I will also need the code to allow the correct commands. as below

1. When button one on the transmitter is pressed , signal the receiver to tell the main board to spin the motor clock-wise until sensor two is pressed.

2. When button two on the transmitter is pressed , signal the receiver to tell the main board to spin the motor anti clock-wise until sensor one is pressed.

I will need the code and the boards made and delivered. the dimensions are restricted to 63mm length x 28mm width x 2mm height. or 30mm length x 30 width x 30 height.

Thanks.

Taidot: Arduino, C-ohjelmointi, sähkötekniikka, elektroniikka, Mikrocontroller

Näytä lisää: record circuit board, printed circuit board research, disadvantages printed circuit board, hs code 85340000, circuit board component abbreviations, hs code for populated printed circuit board, circuit board hs code, circuit board component letters, f1 on circuit board, pcb identification code, circuit board component identification, printed circuit board layout service, job printed circuit board pcb, printed circuit board give advantage disadvantage, design circuit board india, solidworks circuit board, disadvantage printed circuit board, circuit board solid works, printed circuit board design forum india, circuit board cad

Tietoa työnantajasta:
( 0 arvostelua ) Sydney, Australia

Projektin tunnus: #19760315

16 freelanceria on tarjonnut keskimäärin %project_bid_stats_avg_sub_26% %project_currencyDetails_sign_sub_27% tähän työhön

Anthony989

Hello, I am Anthony from Sri lanka. I have 7 years of experience in the filed and I am very much interested in your project. Why you should hire me ? * As a full time freelancer I have my own PCB fabricati Lisää

$140 AUD 7 päivässä
(59 arvostelua)
6.5
MUhammadt429i

I have long experience with 8-bit , 16-bit and 32-bit micro-controllers. I work with Microchip (PIC) , Atmel (AVR , SAM) , ST (STM) , TI (MSP) , Nordic (nRF52), and NXP (LPC) micro-controllers. I use KEIL IDE , Atmel S Lisää

$333 AUD 3 päivässä
(36 arvostelua)
5.8
hayat38402

I am Excellent at the following:  Embedded C Programming.  VHDL/Verilog  Microcontroller like Arduino,RaspberryPi,FPGA, AVR, PIC and STM32.  IDEs like Keil MDK V5, ATmel studio and MPLab XC8.  IOT Technolog Lisää

$155 AUD 3 päivässä
(25 arvostelua)
5.4
Itblast

I've worked for years to perfect the art of laying out a circuit board. So much that I've built an entire business handling projects for high-profile clients from concept to prototyping to production. Whether you need Lisää

$155 AUD 3 päivässä
(1 arvostelu)
2.8
doughy515

I am an expericned electronic engineer for the past 6 years. I will be able to take your idea to a fully working prototype by doing the circuit design, PCB layout, firmware and even a 3D printed case if needed.

$222 AUD 7 päivässä
(1 arvostelu)
2.5
toanasahmed

Hello I ve my own Hackerspace and we are working on these kind of projects with great efficiency We are interested in this project and willing to provide the solution Contact me so that we can discuss this further Your Lisää

$155 AUD 3 päivässä
(3 arvostelua)
2.2
beemf1633

I’m electrical engineer and i'm interested in your Project, and so I would like to offer my services. I will do your work according to your demand.I see you project carefully you are using servo motor for rotating.I ha Lisää

$99 AUD 5 päivässä
(5 arvostelua)
1.5
eltonavieira

Hello I'm an embedded software engineer and I would like to hear about your project requirements to estimate how much effort is needed to complete the job. so I can adjust my bid to job complexity. Best regards

$220 AUD 20 päivässä
(1 arvostelu)
1.1
Provi11

I have about 2 years experience in Arduino C programming and written programs for many arduino and robotics projects. I have also written code for electric vehicle.

$40 AUD 7 päivässä
(1 arvostelu)
1.2
meer11

Hi, I am an Electrical Engineer by profession, an expert in MATLAB, SIMULINK, ARDUINO, AUTOCAD, CREO, etc I will provide a circuit board and code for your project. Also I will be available for any revisions needed. P Lisää

$140 AUD 7 päivässä
(1 arvostelu)
0.0
divinedesignr

Hello, Hope you are doing great. Let’s get you some brief details of us. We are an Innovative Product Design & Development Company, specializing in designing products for Industrial and Mechanical Industries. Lisää

$222 AUD 30 päivässä
(0 arvostelua)
0.0
rama20chandra

experience in embedded software development and Android application development for embedded systems industrial experience in running motors and communication between boards using Bluetooth module

$144 AUD 10 päivässä
(0 arvostelua)
0.0
samuelrvw

I can make fabricate the board and ship it to you. Also once you receive it you can test and if you require support (meaning if there is any bug fix) we can work together to get it up. I can work on the type of MCU tha Lisää

$265 AUD 14 päivässä
(0 arvostelua)
0.0
janiru160

I can do it

$38 AUD 3 päivässä
(0 arvostelua)
0.0
rathinchandra999

I am a professional embedded system engineer. I have checked your drawings. I can easily design the required PCB for you. Please message me for further discussion.

$111 AUD 3 päivässä
(0 arvostelua)
0.0
AventurierWX0

Hello, I am a hobbyist in this field, I am currently working on a circuit board like this so I can provide you with reference work and I am willing to do it for cheap (under the bid amount if time is not a concern for Lisää

$30 AUD 5 päivässä
(0 arvostelua)
0.0