Coin op (pulse) single use lockers using Arduino and/or Raspberry Pi

I am after some code for Arduino and/or Raspberry Pi, along with a basic LCD screen and potentially a relay PCB if needed, that has to perform the following:

- Display a particular message while waiting for a pulse

- When pulse is detected, ask customer to enter locker number

- After locker number is entered, customer enters a 4 digit pin, then re-enters to confirm it

- Code activates an output that opens the selected door, this also turns on an led to show that the locker is unavailable

- When a customer comes back to collect their goods, they press a button which then asks them for their locker number and password.

- Locker then opens and fully resets, ready for next user

Obviously it needs to be programmed that if the passwords are wrong, or another customer is using that locker, it doesn't open, and preferably gives a message on the display.

Need it to work with up to 12 lockers/doors. Also would like a button to clear each locker if a customer forgets their password. If the power goes out, it doesn't need to remember the saved lockers (although that would be nice) it will just be manually reset via the previously mentioned buttons

Taidot: Arduino, Elektroniikka, Raspberry Pi

Näytä lisää: single traffic light using arduino, arduino raspberry pi projects, arduino raspberry pi, 4-20 ma (current loop) sensor board for arduino, raspberry pi and intel galileo, arduino raspberry pi data logger, attendance system using mysql raspberry pi and rfid, arduino raspberry pi communication, best arduino raspberry pi projects, arduino raspberry pi robot, arduino raspberry pi nrf24l01, introduction to computer organization: arm assembly language using the raspberry pi, python arduino raspberry pi, line follower robot using arduino and ir sensor code, arduino raspberry pi xbee communication, assembly language using the raspberry pi pdf, single phase inverter using arduino, arduino raspberry pi zero, water level controller using arduino and ultrasonic sensor code, single phase inverter using arduino code, obstacle avoiding robot using arduino and ir sensor code

Tietoa työnantajasta:
( 1 arvostelu ) BROOKDALE, Australia

Projektin tunnus: #30948886

Myönnetty käyttäjälle:


Dear client, I understand your requirement. I'm an embedded developer. I made similar projects like this before using STM32 and ESP32. One of them is a sanitary napkin vending machine, in which a pulse based coin count Lisää

$250 AUD 7 päivässä
(0 Arvostelua)

31 freelanceria on tarjonnut keskimäärin $490 tähän työhön


Best PCB Design Expert at your doorstep! Dear Client, We have lots of experience in PCB Design so we can design Relay PCB with LED Screen using Arduino and Raspberry Pi for single use lockers while meeting all require Lisää

$500 AUD 2 päivässä
(34 arvostelua)
(129 arvostelua)
(74 arvostelua)

Hey there! I am professional electrical engineer having more than 4 years experience in Arduino Programming, Coding and Projects and simulation on TinkerCad and Proteus. I have expertise in following Microcontrollers Lisää

$450 AUD 6 päivässä
(70 arvostelua)

Hi, I am an embedded developer with more than 7 years of experince with Arduino related systems development. I have very good experience in designing systems using Arduino and off the shelf components and PCB assembly Lisää

$700 AUD 7 päivässä
(42 arvostelua)

I can make you schematic, the code and recommend components (links) for assembling. I suppose PSB is not necessary, with the proper components and modules everything (almost) can be assembled using screw connectors, wi Lisää

$300 AUD 7 päivässä
(104 arvostelua)

Thanks for Freelancer which gives chance to meet you. I hope you are good. I have read your description carefully and understand everything. I have 12 year experience on analog design, Arduino and PCB design. I will u Lisää

$250 AUD 10 päivässä
(26 arvostelua)

Hello I'm an electronics engineer with 10+ years of experience, including Arduino, ESP, STM, and Raspberry. I have all the hardware for the project and am ready to start immediately. Please contact me to discuss the Lisää

$370 AUD 5 päivässä
(12 arvostelua)

FREE OF COST CONSULTATION Dear Client, I can design Relay PCB with LED Screen and using Arduino and Raspberry while meeting all requirements for Coin op (pulse) single use lockers in a quality and timely manner. Plea Lisää

$400 AUD 2 päivässä
(2 arvostelua)

Hi! I am an Electronic engineer, PCB Layout, Circuit Design, microcontroller, STM32 microcontroller, C programming expert having past experiences with ,Altium, arduino, pic, AVR, chipkit and Texas instruments microcont Lisää

$750 AUD 7 päivässä
(12 arvostelua)

Hi Sir! I am student of MSc Mechatronics and Control Engineering. I have done BSc Electrical Engineering. I am very expert in Arduino included its all module. I will give you best work on time.

$300 AUD 5 päivässä
(27 arvostelua)

Hello, We are a team of experienced IoT developers with expertise in raspberry pi. Please share more details about the requirents over a chat. Thank you.

$1667 AUD 40 päivässä
(3 arvostelua)

dear Employer, I have read your clear specification and I will suggest to use a raspberry PI for this functionality. I have a lot of experience with programming for Raspberry and Arduino so I can deliver the program wi Lisää

$350 AUD 7 päivässä
(11 arvostelua)

Dear, client. I am very glad to see your requirement. Because I just finished similar project with yours and your project can be done within 2~3 days. I can simulate your project and it can be helpful for you to test m Lisää

$300 AUD 2 päivässä
(4 arvostelua)

Welcome Sir I can help you in successfully completing your project. I am an expert in the Arduino field. I have done many similar projects for this work. Send me all the details. Here are some of my work I unveiled an Lisää

$250 AUD 7 päivässä
(15 arvostelua)

Dear Sir, I would like to present myself as prospective candidate to do your project. I have sound knowledge and experiences in Arduino, Raspberry Pi and electronic circuit designing. Therefore I would be the best cand Lisää

$400 AUD 7 päivässä
(4 arvostelua)

Hello! I have read the description and I am quite sure that I have the necessary skills and knowledge about the project. I would be pleased to talk about the details via chat. I am a BSc Electrical and Electronics Eng Lisää

$650 AUD 7 päivässä
(7 arvostelua)

Hello, I am interested in your project and I hope to help you realize it, I am passionate about electronics and embedded development and I hope to share with you my knowledge and experience. I can do this work in 7 da Lisää

$400 AUD 7 päivässä
(5 arvostelua)

Hello There,, - I have 8+ years of experience with different Micro controllers, ESP32, Arduino, ESP6266, Embedded C, C++ and Linux. - I have worked on different microcontrollers like PIC, ATSAM, STM32 etc. - I hav Lisää

$700 AUD 5 päivässä
(1 arvostelu)

Hi! I have understood your requirnments about your project with every detail of it. I am an Electrical Engineer with more then 9 years experience in electronics, circuit design, PCB layout, Verilog, FPGA, Embadded Syst Lisää

$750 AUD 7 päivässä
(0 arvostelua)