Vcc tirmizi työt
I am in need of a freelancer who can provide a Virtual Credit Card (VCC) or top-up service for my online purchases in Argentina (Microsoft). The desired currency for the VCC or top-up service should be in Argentinian Pesos. I do not have a specific bank or company in mind, so any reputable bank or company will do. Skills and Experience: - Experience in providing VCC or top-up services - Knowledge of reputable banks or companies that offer such services in Argentina
I am looking for a freelancer from Argentina who can help me for the purpose of purchasing a specific Microsoft product, in the currency Argentine Peso. Skills and experience required: - Familiarity with Argentina VCC or top-up services - Knowledge of reputable banks or companies that offer such services in Argentina The transaction will cost 4.556 Peso and i will need 4 of these.
I am in need of a freelancer who can provide a Virtual Credit Card (VCC) or top-up service for my online purchases in Argentina (Microsoft). The desired currency for the VCC or top-up service should be in Argentinian Pesos. I do not have a specific bank or company in mind, so any reputable bank or company will do. Skills and Experience: - Experience in providing VCC or top-up services - Knowledge of reputable banks or companies that offer such services in Argentina
...someone who knows their stuff. I work in PCB design but I am not yet so good at circuit design. So I just need a schematic making. I am looking for a laser diode controller circuit. The diode is high power for engraving wood, I am looking at using the Nichia NUBM44 but open to other suggestions. Will obviously also use a heatsink +fan for cooling. The circuit should consist of three inputs, +VCC, GND and the PWM signal. pick your own values for source voltage and input signal but try to stick to standard numbers. I basically just need the diode to be controlled by the PWM signal, that's not hard to do with an NPN transistor and a current limiting resistor. Though I would also like something to make sure there is a constant stable current being fed to the diode, this is al...
Custom Avatar - Style: Cartoon - Character/Personality: GoBot themed avatar - Revisions: 2 I am looking for a talented artist to create a custom cartoon avatar for me. Avatar should be loosely based on the old GoBots cartoon and have the the acronym VCC represented. The avatar should be based on a specific character, namely a GoBot themed avatar. The character should be unique and have its own distinctive personality. I would like the artist to provide up to 2 revisions for the avatar design. This will ensure that we can fine-tune the details and make any necessary adjustments to achieve the desired look. Ideal Skills and Experience: - Strong illustration skills, particularly in cartoon style - Experience in creating character designs - Ability to bring personality and uniquen...
Using a wemos lolin lite esp32 development board how to wire to a 128x64 display with controller SSD1309 that has connections VCC, GND, DIN, CLK, CS, DC, RST give an exact wire pin out to the Wemos. You must produce functioning code that will display a bitmap image on the display. Here is the oled display: https://www.amazon.com/waveshare-1-51inch-Transparent-OLED-Independent/dp/B0B8N46G24/ref=sr_1_3?crid=1PPE3UAGWPTBZ&keywords=transparent+oled&qid=1700370317&sprefix=transparent+ole%2Caps%2C88&sr=8-3
want help to get something online in shopping VCC
I am in need of a power supply expert to assist me with a project. The specific expertise I need is Power Supply Design, and I alrea...prepared for the project. I am looking for an engineer who is available to work on this project remotely and support me for a solution to fix the identified problem. Attached documents: 1. Schematic PSU with SMR20.8/10111 2. Datasheet SMR20.8/10111 3. Schematic2 to be used with connected ESP32-S3 and Display 4. Oscillograph records referred to schematic2 (Channel1: VCC_IN, Channel 2: +3.3V, Channel 3: VCC) 5. I5 conducted radio frequency report The product (room controller) has failed the requirements for the CE certification especially in "I5 conducted radio frequency". The expert should have good knowledge in power supply design and CE ...
I am looking for a vps provider or purchaser with knowledge about vcc and rdp/vpn to create and manage vps accounts and server purchase for us on daily basis. It's going to be a ongoing task and must be serious about timeline. Accounts preferred are ovh and hostwinds.
Circuit #1) The goal is to have a circuit to give/cut power (+3.3v / +5v) to sub ICs/sensors, command by a microcontroller pin. Must cut the input voltage (circuit must be placed between VCC and IC) = high-side switch. Circuit #2) The goal is to have a circuit to enable/cut I2C bus (+3.3v / +5v), command by a microcontroller pin. We want +3.3v and +5v sensors to be connected on the same I2C bus - what about pull-up resistor ? Remarks: If power is cut (by circuit #1), power must not leak through I2C pull-up resistors. Maybe circuit #2 is not necessary if we can be sure that no current leak through pull-up resistors when cut the power. Guidelines : - Simplest as possible (the less or cheaper components) - Easy to find component (AliExpress, Mouser, ...) - Easy to hand-soldering c...
VCC is going to set up a new building with 10 new labs for the upcoming semester and they require patch management for Desktops, Servers, and all portable devices. Also, VCC expects its office with a new network deployment for its course instructors to work and connect easily to VCC network in Wireless mode through their laptops and mobile devices. The Deployment is based on the following: • 50 Microsoft Windows 10 laptops • 200 Microsoft Windows 10 desktops • 150 Mobile Devices (Either Android/Apple) • 20 Microsoft Windows Servers • 2 Cisco ASA Security appliances (firewalls) • 2 Cisco Core Switch • 12 Cisco Distribution Switches • 20 Cisco Wireless Base Stations The project sponsor would like you to base your project on the N...
Job Description -------------------------- I have a batch of Chinese made volt meters with 7 segment led displays these are pre-programmed for input zero to 33 volt and output will d...segment led displays these are pre-programmed for input zero to 33 volt and output will display the voltage with 3 decimal places. If possible I want to reprogram the MC for input zero to 4 volts and output zero to 2000 V on the display (ratio 1:500) Laser engraving on micro is S033 PHVG 639Y , but I can not find any specifications for the code (see images) Circuit board has connections for GND, VCC, Send, Receive I am happy to post a sample of the voltmeter to the successfull freelancer. On completion of the job I need a working code and instruction how to upload the code to the voltmeters. G...
I WANT VCC virtual visa or master card to make online purchasing ty
We need to develop mobile wallet ( android - IOS ) -Top up them wallet by using payment gateway . -Transfer the money between the wallet . -Generate VCC for the wallet. -The wallet members they can use VCC for purchasing. -Exchange currency - please who have experience in this project only contact , who don't have any experience in this project don't contact me - send to me your previous work in projects like that
hello, i need indian kotak or hdfc vcc. bid for 10 vcc thanks
We are looking for long term supplier for VCC or similar for AMZ Seller accounts.
I need credit cards for Etsy to open shops. Polish virtual credit cards needed
Tasks are to submit some ads to multiple paid sites. You must have all tools vcc, cc etc Any bid from outside the united states, Canada, Australia and United Kingdom.. WILL BE REJECTED!
...connected to the SDA pin of the SHT31 - GPIO05 should be connected to the SCL pin of the SHT31 - There should be connectors for the VCC, GND, TX, and RX pins. 22AWG wires will be plugged in. Here are the connections for the SHT31 - VDD/5 should be connected to the VCC - VSS/8 should be connected to the GND - There should be a 100nF SMD capacitor between the VDD/5 and VSS/8 pins. - The SDA/1 pin should be pulled-up with a 10kOhm SMD resistor. - The SCL/4 pin should be pulled-up with a 10kOhm SMD resistor. - The R/7 pin should be connected to GND. - The ADDR/2 pin should be connected to GND. - The ALERT/3 pin should be left floating. - The RESET/6 pin should be connected to VCC. - Die pad should be soldered and left floating. - The PCB around the SHT31D chip should b...
Hi Dionesio M., How have you been? This is Rudy from velvet crown/ poetic juices! It’s time to work with the best! We need you again! We need a baseball jersey design for vcc. I can send you references and colors if your available to work! Thanks in advance!
bing ads account with own billing or vcc for our use, this is not one time we need it on regular basis
...electrical components are identified by a manufacturer's part number, and ideally by a recommended source / brand P/N when many suppliers exist and the performance of the component varies considerably among the sources. The circuit begins with a USB A recetacle/female connector that the USB Device would connect to and ends with a USB A plug/male connector Protects all five of the USB pins/lines (VCC, D-, D+, ID, GND) from over voltage, short circuit, reverse polarity, etc. At least one LED provides indication of a successful power transfer connection. Any additional LEDs that can provide useful information would be a bonus. The USB data capabilities (2.0, 3.0, ...) and performance, as well as the charging capabilities are not adversely affected by the insertion of the d...
Hello Wang I want to change the Audio circuit. Delete BA3121 and TDA2822. Please use LM4861 with 5V DC Vcc. Please change Schematic for approval first Please add second LDO 3.3V regulator for optional use when we need 3.3 for U1 but still need 5V for Audio. Please change PIC footprint. Use PIC18F24-I/SS-ND 28SSOP
I got 2 boards, 1 - board with ESP32 with shift register.... , working on TTL level 3.3V 2 - 16x02 LCD board with 5V backlight supply and 5V VCC supply...., but to be interfaced with 3.3V of shift register output board is ready, shift register tested and working ok... but unable to display any data on LCD, need support for the same only for coding with arduino IDE to show data on LCD
Use two single-bit inputs and the on-board LED as an output. Write a program that reacts to the inputs and the past states of the inputs. Denoting the two inputs by 0s and 1s, let your program activate different tasks given the input sequence, say, the state 11, followed by 10, followed by 00, etc. The inputs may be connected to wires that you can touch to VCC or Ground terminals of the board.
Project description: Ruggedized, gamepad-style drone controller PCB. We need EAGLE Schematic divided into A4 frames + PCB design + clean BOM + PCB production files + 3D model. Needed features: - 2 pins on main SF8-B Weipu connector are meant for VCC and GND. VCC will be in range 5-36V and step down circui that makes 5V on output should be able to provide 5V of output in the whole VCC range - ESP32-S3-WROOM-1-N16 as microcontroller - solder pads for connecting main SF8-B Weipu connector - 2x rugged joysticks input (solder pads as with main connector, 4x ADC channel, supply voltage selectable with 0R jumper 3.3/5V) - 10x button inputs with debounce circuit - Generally the device is powered from computer's 5-36V DC bus but we want to have the option for wir...
I have been looking for a freelancer who can develop RFID card reader with following requirement. requirement: - detectable distance: 3cm - input voltage: 3.3V - communication: UART - board size: 59.5*59mm - interface: PH2.0 4P(1-VCC, 2-TX, 3-RX, 4-GND) You are free to choose the RFID chip, but should ensure the requirement of detectable distance and stock. You should provide pcb design file(Altium Designer) and firmware at the end of project.
I am using an arduino robot with components: Arduino Uno Adafruit Motor Shield v2.3 2x Stepper motors HC-SR04 ultrasonic sensor with pins: (5V - VCC, 10 - TRIG, 13 - ECHO, GND - GND) 9V batteries And when i upload my code the robot does nothing where it suppose to find it's way out a physical maze using the shortest route generated. Can anyone find the issues or the missing libraries from the code and optimize it? The code and for further info please let me know so i can provide upon request. Everything is ready and the code is complete but i might be missing something simple.
Rekisteröidy tai kirjaudu sisään nähdäksesi tiedot.
compare the four parameters compare the three parts with the 4 parameters: quiescent power, active power, voltage vcc, and TID radiation from the website that i sent you and then highlight where you got it from
...control circuit. We will source all of the parts, you are just making the KiCad design. You will layout a board using KiCad Software. 1) Components a. Qty 1 8 pin connector connecter type is unspecified TBA i. Vcc ii. Ground iii. A Input iv. B Input v. C Input vi. D Input vii. Extra light 1 viii. Extra light 2 b. Qty 1 74154 Decoder c. Qty 1 socket for 74154 d. Qty 12 10mm LEDs e. QTY 12 100 ohm ¼ watt resistors 2) Connections a. Vcc connects to: i. Pin 24 of 74154 ii. 12 resistors b. Ground Connects to: i. Pins 12,18,19 of 74154 c. A Input to Pin 23 of 74154 from connector d. B Input to Pin 22 e. C Input to
An extension should capture the particular area in the screen and load the captured data as text into the desired fields. find an attached Image for the reference This is how the data should load 1 ASNS 2 FLTR1 3 DIM 4 COFF 5 FLTR2 6 GND 7 ISNS 8 GATE 9 VCC 10 BLDR
I need an electric schematic on eagle cad. using a Arduino Uno, GARMIN lidar sensor v3, and MPU-6050 Module. I would need by December 6 7pm east...when device is enabled) 680uF capacitor (+) to Arduino 5v 680uF capacitor (-) to Arduino GND See the Operation Manual for wiring diagrams and more information: These are the connections for the buzzer,acceleromior, button Buzzer: (+) to digital pin 12 (-) to Ground acceleromitor: Vcc to 5V GND to GND SDA and SCL to SDA an SCL of arduino button: pin 7 GND Vibration Motor: positive end to the 5V power source negative end to the mosfet mosfet middle lead to digital pin 5 of the arduino mosfet third lead to GND
...side + 2 bottom side) 2 Buttons I required additional 2 SMD Buttons & modifications of the Pins to be mapped to the following: //INPUTS : with VCC&GND placed at the LEFT edge of the PCB with Male Pins and SMD Soldering pads for the Signal PIN, 2 GND @bottom, 2 VCC @TOP #define A0 36 #define A1 39 #define A2 34 #define A3 35 #define A4 32 #define A5 33 #define A6 25 #define A7 26 #define A8 27 #define A9 14 #define A10 12 // BUTTON 1 #define A11 13 //BUTTON 2 //OUTPUTS : with VCC&GND placed at the LEFT edge of the PCB with Male Pins and SMD Soldering pads for the Signal PIN, 2 GND @bottom, 2 VCC @TOP #define O0 19 // #define O1 18 // #define O2 5 // #define O3 17 // #define O4 ...
WANT SOMEONE PROVIDE VCC SERVICES VIRTUAL VISA CARD
want someone help me to get VCC CHARGED
I WANT HELP TO GET VCC CHARGED 50$ FOR ONLINE SHOPPING
FIRST TO SOLVE WINS THE BID: I have an ARUDINO UNO connected to a PCF8575 with the following. - PCF GND - ARDUINO GND - SCL - SCL - SDA - SDA - VCC - VCC Not using the INIT (or interrupt) Using PCF8575 PCF(0x20); i am able to read from pins 0 - 7 with (0)....(7) but when trying to read from PINS10-17 i can not do so with (10); Solve the task.
i want VCC help to get it want financial expert and someone know what vcc means
